Yamaha FZ6-NV Page 35 Owner'S Manual Download | Manualshive

Page: 35 / 90

background image

PRE-OPERATION CHECKS

4-2

4

EAU15603

Pre-operation check list

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.

Engine oil

• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

Coolant

• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Rear brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Clutch

• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.

U1B322E0.book Page 2 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
33
34
35
36
37
...
»

Summary of Contents for FZ6-NV



























































































Reviews:

No comments

Related manuals for FZ6-NV

Brand: ZARD Pages: 2

Brand: Ohlins Pages: 8

TXT PRO - PART LIST CHASSIS 2003

Brand: GAS GAS Pages: 36

Brand: MOTO GUZZI Pages: 61

Brand: Memphis Shades Pages: 2

Brand: GAS GAS Pages: 131

Brand: Honda Pages: 93

640 LC4 Adventure

Brand: KTM Pages: 59

Brand: Royal Enfield Pages: 110

Brand: BMW Pages: 205

Brand: Malaguti Pages: 272

Brand: Legend Pages: 2

Brand: Star Motorcycles Pages: 19

Brand: RIEJU Pages: 147

DUCATI HYPERMOTARD 1100 EVO SP

Brand: Peg-Perego Pages: 40

Brand: DAQRI Pages: 20

Brand: hepco & becker Pages: 8

Brand: Yamaha Pages: 758

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands