Yamaha FZ6-N Owner'S Manual Download Page 81

Page: 81 / 88

SPECIFICATIONS

8-2

Gear ratio:

1st:

37/13 (2.846)

2nd:

37/19 (1.947)

3rd:

28/18 (1.556)

4th:

32/24 (1.333)

5th:

25/21 (1.190)

6th:

26/24 (1.083)

Chassis:

Frame type:

Diamond

Caster angle:

25.00 °

Trail:

97.5 mm (3.84 in)

Front tire:

Type:

Tubeless

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

BRIDGESTONE/BT020F GG

Manufacturer/model:

DUNLOP/D252F

Rear tire:

Type:

Tubeless

Size:

180/55 ZR17M/C (73W)

Manufacturer/model:

BRIDGESTONE/BT020R GG

Manufacturer/model:

DUNLOP/D252

Loading:

Maximum load:

196 kg (432 lb)
(Total weight of rider, passenger, cargo and
accessories)

Tire air pressure (measured on cold
tires):

Loading condition:

0–90 kg (0–198 lb)
Front:

225 kPa (33 psi) (2.25 kgf/cm²)

Rear:

250 kPa (36 psi) (2.50 kgf/cm²)

Loading condition:

90–196 kg (198–432 lb)
Front:

250 kPa (36 psi) (2.50 kgf/cm²)

Rear:

290 kPa (42 psi) (2.90 kgf/cm²)

High-speed riding:

Front:

225 kPa (33 psi) (2.25 kgf/cm²)

Rear:

250 kPa (36 psi) (2.50 kgf/cm²)

Front wheel:

Wheel type:

Cast wheel

Rim size:

17M/C x MT3.50

Rear wheel:

Wheel type:

Cast wheel

Rim size:

17M/C x MT5.50

Front brake:

Type:

Dual disc brake

Operation:

Right hand operation

Recommended fluid:

DOT 4

Rear brake:

Type:

Single disc brake

Operation:

Right foot operation

Recommended fluid:

DOT 4

Front suspension:

Type:

Telescopic fork

Spring/shock absorber type:

Coil spring/oil damper

Wheel travel:

130.0 mm (5.12 in)

Rear suspension:

Type:

Swingarm (monocross)

Spring/shock absorber type:

Coil spring/gas-oil damper

Wheel travel:

130.0 mm (5.12 in)

U1B3E1E0.book Page 2 Thursday, July 8, 2004 11:49 AM

Summary of Contents for FZ6-N

























































































Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands

Yamaha FZ6-N, Owner'S Manual

Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands