Yamaha FZ6-N Owner'S Manual Download Page 28 | Manualshive

Page: 28 / 88

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-14

3

2. Push the rear of the seat down to

lock it in place.

3. Remove the key.

NOTE:

Make sure that the seat is properly se-
cured before riding.

EAU14421

Storage compartment

This storage compartment is designed
to hold a genuine Yamaha U-LOCK.
(Other locks may not fit.) When placing
a U-LOCK in the storage compartment,
securely fasten it with the straps. When
the U-LOCK is not in the storage com-
partment, be sure to secure the straps
to prevent losing them.

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of 196 kg (432 lb) for the ve-
hicle.

1. Projection
2. Seat holder

1. U-LOCK bar (optional)

2. Yamaha U-LOCK (optional)

3. Strap

U1B3E1E0.book Page 14 Thursday, July 8, 2004 11:49 AM

«
...
26
27
28
29
30
...
»

Summary of Contents for FZ6-N

























































































Reviews:

No comments

Related manuals for FZ6-N

Brand: GAS GAS Pages: 57

Brand: SCORPION Pages: 12

Brand: Sym Pages: 31

Brand: National Cycle Pages: 5

Brand: Shark Pages: 52

Brand: LAZER Pages: 11

Brand: TREND Pages: 38

Brand: PUIG Pages: 6

Brand: MW TOOLS Pages: 9

RACE 11621C0520

Brand: Yoshimura Pages: 7

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 388

Brand: Yamaha Pages: 18

Brand: BMW Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands