Yamaha FZ6-N Owner'S Manual Download Page 66

Page: 66 / 88

PERIODIC MAINTENANCE AND MINOR REPAIR

6-28

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU34380

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the bolts on each side.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

Specified fuses:

Main fuse:

30.0 A

Headlight fuse:

20.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

10.0 A

Radiator fan fuse:

20.0 A

Electronic fuel injection fuse:

10.0 A

Backup fuse:

10.0 A

Parking lighting fuse:

10.0 A

1. Bolt

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder
2. Headlight bulb

U1B3E1E0.book Page 28 Thursday, July 8, 2004 11:49 AM

Summary of Contents for FZ6-N

























































































Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands

Yamaha FZ6-N, Owner'S Manual

Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands