Yamaha FZ6-N Owner'S Manual Download Page 62

Page: 62 / 88

PERIODIC MAINTENANCE AND MINOR REPAIR

6-24

EAUM1650

Lubricating the swingarm
pivots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

EAU23271

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

WARNING

EWA10750

Securely support the vehicle so that
there is no danger of it falling over.

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

CAUTION:

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

Recommended lubricant:

Lithium-soap-based grease

U1B3E1E0.book Page 24 Thursday, July 8, 2004 11:49 AM

Summary of Contents for FZ6-N

























































































Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands

Yamaha FZ6-N, Owner'S Manual

Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands