background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-8

6

NOTE:

An oil filter wrench is available at a
Yamaha dealer.

5. Apply a thin coat of engine oil to

the O-ring of the new oil filter car-
tridge.

NOTE:

Make sure that the O-ring is properly
seated.

6. Install the new oil filter cartridge

with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.

7. Install the engine oil drain bolt, and

then tighten it to the specified
torque.

NOTE:

Check the washer for damage and re-
place it if necessary.

8. Add the specified amount of the

recommended engine oil, and then
install and tighten the oil filler cap.

CAUTION:

ECA11620

In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Make sure that no foreign mate-
rial enters the crankcase.

9. Start the engine, and then let it idle

for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.

1. O-ring

1. Torque wrench

Tightening torque:

Oil filter cartridge:

17 Nm (1.7 m·kgf, 12 ft·lbf)

Tightening torque:

Engine oil drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lbf)

Recommended engine oil:

See page 8-1.

Oil quantity:

Without oil filter cartridge replace-
ment:

2.50 L (2.64 US qt) (2.20 Imp.qt)

With oil filter cartridge replacement:

2.80 L (2.96 US qt) (2.46 Imp.qt)

U1B3E1E0.book  Page 8  Thursday, July 8, 2004  11:49 AM

Summary of Contents for FZ6-N

























































































Reviews: