Yamaha FS1R, Data List

Page: 36 / 44

36
2.Channel Messages
2.1 Transmission
2.1.1 Control Change
Assigned controller numbers are output when built-in knobs are turned.
Cntrl# Parameter Data Range
73 Attack Time 0~127
72 Release Time 0~127
1~31, 33~95 Formant Control 0~127
1~31, 33~95 FM Control 0~127
1~31, 33~95 Knob 1 0~127
1~31, 33~95 Knob 2 0~127
1~31, 33~95 Knob 3 0~127
1~31, 33~95 Knob 4 0~127
Note: Attack Time to FM Control are assigned to knobs with the upper LED lit. Knob 1 to 4
are assigned with the lower LED lit.
2.2 Reception
2.2.1 Note On/Off
2.2.1.1 Note Off
key range = C-2~G8
velocity range = not received
2.2.1.2 Note On / Off
key range = C-2~G8
velocity range = 0~127 (0 = Note off)
2.2.2 Control Change
Parameters in the following table are controllable using MIDI. A part that can receives multiple
channels operates by those channels in the received order.
Cntrl# Parameter Data Range
0 Bank Select MSB 0~127 *1
32 Bank Select LSB 0~127 *1
1 Modulation wheel 0~127
5 Portamento Time 0~127 *2
6 Data Entry 0~127 *2, *3
7 Volume 0~127 *2, *4
10 Pan 0~127 *2, *4
11 Expression 0~127
64 Sustain (Hold1) 0, 127
65 Portamento Switch 0, 127 *2
71 Harmonic Content 0~127 *2
72 Release Time 0~127 *2
73 Attack Time 0~127 *2
74 Brightness 0~127 *2
91 Reverb Send 0~127 *2
93 Variation Send 0~127 *2
1~31, 33~95 BC (default: 2) 0~127
1~31, 33~95 FC (default: 4) 0~127
1~31, 33~95 Formant Control 0~127 *2
1~31, 33~95 FM Control 0~127 *2
1~31, 33~95 Knob 1~4 0~127
1~31, 33~95 MIDI Control 1~4 0~127
98 NRPN LSB 8~102 *3
99 NRPN MSB 1 *3
100 RPN LSB 0~2 *3
101 RPN MSB 0 *3
*1: Refer to "2.2.3 Program Change."
*2: Corresponding parameter values directly change with control changes, without using the
control matrix. Those values become reference points for control changes routed by the control
matrix, which are not reset by Reset All Controllers.
*3: Parameters that follow are controllable using NRPN or RPN massages.
NRPN Data Entry Part Parameter Data Range
MSB LSB MSB
----------------------------------------------------------
01H 08H 00H~40H~7FH LFO1 Speed -64~+0~+63
01H 09H 00H~40H~7FH LFO1 Pmod -64~+0~+63
01H 0AH 00H~40H~7FH LFO1 Delay -64~+0~+63
01H 0BH 00H~40H~7FH LFO2 Speed -64~+0~+63
01H 0CH 00H~40H~7FH LFO2 FltMod -64~+0~+63
01H 20H 00H~40H~7FH Filter Freq -64~+0~+63
01H 21H 00H~40H~7FH Filter Reso -64~+0~+63
01H 63H 00H~40H~7FH Attack Time -64~+0~+63
01H 64H 00H~40H~7FH Decay Time -64~+0~+63
01H 66H 00H~40H~7FH ReleaseTime -64~+0~+63
RPN Data Entry Part Parameter Data Range
MSB LSB MSB
----------------------------------------------------------
00H 00H 00H~18H PB Range +0, +1~+24
PB Range Lo - 1~-24
00H 01H 0FH~40H~70H Detune -64~+0~+63
00H 02H 28H~40H~58H Note Shift -24~+0~+24
On reception of Pitch Bend Range, PB Range Lo is set to a minus value of received value.
*4: With "Program Change Mode = perform," Performance Volume and Pan are controllable using
Performance Channel. With "Program Change Mode = multi," Performance Volume and Pan
are controllable using Performance Channel while Part Volume and Pan are controllable using
Part Receivee Channel.
2.2.3 Program Change
On reception of Program Change, FS1R operates as follows.
Receives Program Change is received only in PLAY MODE.
In case "Receive Program Change = off" is selected in system setup, Bank Select and Program
Change are not received. With "Receive Program Change = on" and "Receive Bank Select = off,
"Bank Select is not received. On reception of Program Change, a voice or performance program
(1~128) , depending on the Program Change Mode setting, from the current bank is selected.
With "Program Change Mode = perform," a performance program is selected using Performance
Channel. With "Program Change Mode = multi," a performance program is selected using
Performance Channel and a voice program is selected using Part Receive Channel.
Bank Select and Program Change data bytes are as follow.
BANK SELECT $Bn, $00, $3F (MSB)
$Bn, $20, $00~$0B or $40~$43 (LSB)
PROGRAM CHANGE $Cn, $00~$7F
Bank Select other than found in the above table is ignored. Thus, any bank selection does not take place and a
following Program Change selects from the current bank that is not changed.
2.2.3.1 Performance Program Change
Bank Select or Program Change for a performance is received using Performance Channel, as
follows.
1-16 : Received only specified channel.
all : Received all channels (OMNI ON) .
off : Not received.
2.2.3.2 Voice Program Change
Bank Select or Program Change for a voice is received using Part Receive Channel (Part
Receive Channel to Part Receive Channel Max) . With "Part Receive Channel = pfm," Part
Receive Channel matches Performance Channel.
2.2.4 Pitch Bend Change
FS1R receives only Pitch Bend Change MSB. A part assigned with multiple channels can sound
separately according to Pitch Bend Change on different channels.
2.2.5 After Touch
After Touch is received on Receive Channel (s) specified. A part assigned with multiple channels
equivalently receives After Touch on different channels, giving proiority to last reception of this
message. The 3rd byte of Polyphonic After Touch is ignored and processed as Channel After
Touch.
2.2.6 Channel Mode Message
Cntrl# Parameter Data Range
120 All Sound Off 0
121 Reset All Controller 0 *1
123 ll Notes Off 0
126 Mono 0 *2
127 Pol 0
*1 A default value for each message reception is as follows.
$00 for Control Change other than Bank Select and After Touch. Control Changes set to route in
the control matrix to affect part parameters have their corresponding part parameter values
(last edited). Control Changes that can directly change parameters without the control matrix
are not reset by Reset All Controllers, since their values are referred to by other Control
Changes for the same parameters via the matrix.
Sustain = $00 (off)
Expression = $7F
RPN, NRPN = $7F (Null)
Pitch Bend = $00, $40 (Center)
*2 The 3rd byte is ignored.
Bank No.MSB / LSB PGM CNG No.
Voice INTERNAL 63($3F) / 0($00) 1~128($00~$7F)
PRESET A 63($3F) / 1($01)
: :
PRESET K 63($3F) / 11($0B)
Performance INTERNAL 63($3F) / 64($40) 1~128($00~$7F)
PRESET A 63($3F) / 65($41)
PRESET B 63($3F) / 66($42)
PRESET C 63($3F) / 67($43)
Datalist/E 10/21/98 8:32 PM Page 36