Yamaha FL150A Owner'S Manual Download

Page: 34 / 90

Instruments and indicators

The clock operates on battery power. Discon-
necting the battery will stop the clock. Reset
the clock after connecting the battery.

EMU36080

Voltmeter

The voltmeter displays the charge of the bat-
tery in volts(V).

EMU26721

Fuel level-alert indicator

If the fuel level decreases to one segment, the
fuel level alert segment will blink.
Do not continue to operate the engine with full
throttle if an alert device has activated. Get
back to the port within trolling engine speed.

NOTICE:

Running out of fuel can damage

the engine.

[ECM01770]

EMU26732

Low battery voltage-alert indicator

If battery voltage drops, the display will auto-
matically turn on and blink.

Get back to the port soon if an alert device has
activated. For charging the battery, consult
your Yamaha dealer.

EMU26741

Fuel management meter

The fuel management meter shows the state
of the fuel consumption while the engine is
running.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU26752

Fuel flow meter

The fuel flow meter displays the amount of
fuel flow over a one-hour period, at the current
rate of engine operation.

1. Fuel level-alert segment

1. Low battery indicator

1. Fuel flow meter

2. Fuel consumption meter / Fuel economy

meter / Twin engine speed synchronizer

3. Water separator-alert indicator (operates

only if the sensor has been installed)

ZMU01748

U63P7AE0.book Page 28 Thursday, February 25, 2010 1:14 PM

Summary of Contents for FL150A



























































































Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands

Yamaha FL150A, Owner'S Manual

Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands