Yamaha FL150A Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 90

background image

Specifications and requirements

10

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. research octane:

90

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil group 1*:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil group 2*:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL

Total engine oil quantity (oil pan capacity):

5.2 L (5.50 US qt, 4.58 Imp.qt)

Lubrication:

Wet sump

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F150AET 0.980 L (1.036 US qt,
0.862 Imp.qt)
F150AET1 0.980 L (1.036 US qt,
0.862 Imp.qt)
FL150AET 0.870 L (0.920 US qt,
0.766 Imp.qt)
FL150AET1 0.870 L (0.920 US qt,
0.766 Imp.qt)

Tightening torque for engine:

Spark plug:

25.0 Nm (2.55 kgf-m, 18.4 ft-lb)

Propeller nut:

55.0 Nm (5.61 kgf-m, 40.6 ft-lb)

Engine oil drain bolt:

28.0 Nm (2.86 kgf-m, 20.7 ft-lb)

Engine oil filter:

18.0 Nm (1.84 kgf-m, 13.3 ft-lb)

Noise and vibration level:

Operator sound pressure level (ICOMIA
39/94 and 40/94):

79.6 dB(A)

EMU33554

Installation requirements

EMU33564

Boat horsepower rating

WARNING

EWM01560

Overpowering a boat can cause severe in-
stability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your out-
board motor(s) does not exceed the boats
maximum horsepower rating. See the boat’s
capacity plate or contact the manufacturer.

EMU33571

Mounting motor

WARNING

EWM01570

●

Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control,
or fire hazards.

●

Because the motor is very heavy, spe-
cial equipment and training is required
to mount it safely.

Your dealer or other person experienced in
proper rigging should mount the motor using
correct equipment and complete rigging in-
structions. For further information, see page
39.

EMU33581

Remote control requirements

WARNING

EWM01580

●

If the engine starts in gear, the boat can
move suddenly and unexpectedly, pos-
sibly causing a collision or throwing
passengers overboard.

●

If the engine ever starts in gear, the
start-in-gear protection device is not
working correctly and you should dis-
continue using the outboard. Contact
your Yamaha dealer.

U63P7AE0.book Page 10 Thursday, February 25, 2010 1:14 PM

«
...
14
15
16
17
18
...
»

Summary of Contents for FL150A



























































































Reviews:

No comments

Related manuals for FL150A

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 64

RHINO VAP133-ACP

Brand: Octek Pages: 66

Brand: Advantech Pages: 90

Brand: Supero Pages: 90

Brand: Inrevium Pages: 57

Brand: AOpen Pages: 8

975X Platinum Series

Brand: MSI Pages: 157

Brand: Texas Instruments Pages: 15

Brand: ASROCK Pages: 293

Brand: Analog Devices Pages: 7

Brand: Supermicro Pages: 95

Side-Power SX100/185T

Brand: SLEIPNER MOTOR AS Pages: 16

Brand: Nuvoton Pages: 11

Brand: MSI Pages: 77

Brand: Texas Instruments Pages: 24

Brand: Curtis Instruments Pages: 46

Brand: Reely Pages: 8

Brand: Raspberry Pi Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands