Yamaha FL150A Owner'S Manual Download Page 89

Page: 89 / 90

Trouble Recovery

Unscrew the filter cup from the filter hous-
ing.

NOTICE:

Be careful not to twist the

water detection switch lead when un-
screwing the filter cup.

[ECM01960]

Drain the water in the filter cup by soaking
it up with a rag.

Firmly screw the filter cup onto the filter
housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01970]

Connect the water detection switch cou-
pler securely until a click is heard.

Install the top cowling.

Start the engine and make sure that the
water separator-alert indicator remains
off. Have a Yamaha dealer inspect the
outboard motor after returning to port.

EMU33501

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immediate-
ly.

NOTICE:

Do not attempt to run the out-

board motor until it has been completely
inspected.

[ECM00401]

1. Filter cup
2. Water detection switch lead

1. Water detection switch coupler

ZMU06223

U63P7AE0.book Page 83 Thursday, February 25, 2010 1:14 PM

Summary of Contents for FL150A



























































































Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands

Yamaha FL150A, Owner'S Manual

Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands