Yamaha FL150A Owner'S Manual Download

Page: 30 / 90

Components

EMU26462

Flushing device

This device is used to clean the cooling water
passages of the motor using a garden hose
and tap water.

TIP:

For details on usage, see page 60.

EMU35562

Fuel filter/Water separator

This engine has a combination fuel filter/water
separator and associated alert system. If wa-
ter separated from the fuel exceeds a specific
volume, the alert device of 6Y8 Multifunction
Tachometer will activate.

Activation of alert device

●

The water separator-alert indicator of 6Y8
Multifunction Tachometer will blink.

●

The buzzer will sound intermittently only
when the gear shift is in neutral.

●

If the alert system has activated, stop the
engine and consult a Yamaha dealer imme-
diately.

1. Cowling lock lever(s)

1. Flushing device

ZMU05348

U63P7AE0.book Page 24 Thursday, February 25, 2010 1:14 PM

Summary of Contents for FL150A



























































































Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands

Yamaha FL150A, Owner'S Manual

Search results

Summary of Contents for FL150A

Reviews:

Related manuals for FL150A

Brands by name

Popular brands