manualshive.com logo in svg

Yamaha F15D, Owner'S Manual, Page: 22 / 92

Share
Download
Yamaha F15D Owner'S Manual Download Page 22

 

Basic components

 

17

 

EMU25970

 

Throttle friction adjuster

 

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.

WARNING

 

EWM00030 

 

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move throttle lever or grip,

 

which could result in an accident.

 

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

 

EMU25990

 

Engine stop lanyard switch

 

The lock plate must be attached to the en-
gine stop switch for the engine to run. The
lanyard should be attached to a secure place
on the operator’s clothing, or arm or leg.
Should the operator fall overboard or leave
the helm, the lanyard will pull out the lock
plate, stopping ignition to the engine. This
will prevent the boat from running away un-
der power.

WARNING

 

EWM00120 

 

●

 

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

 

●

 

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

 

●

 

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the

 

boat to be thrown forward.

 

1. Throttle indicator

ZMU02000

1

ZMU02001

Summary of Contents for F15D





























































































Reviews:

No comments