manualshive.com logo in svg

Yamaha F15D, Owner'S Manual, Page: 20 / 92

Share
Download
Yamaha F15D Owner'S Manual Download Page 20

 

Basic components

 

15

 

EMU26201

 

Neutral interlock trigger

 

To shift out of neutral, first pull the neutral in-
terlock trigger up.

 

EMU26211

 

Neutral throttle lever

 

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

 

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

 

position.

 

EMU26221

 

Choke switch

 

To activate the choke system, press in the
main switch while the key is turned to the
“

” (on) or “

” (start) position. The

choke system will then supply the rich fuel
mixture required to start the engine. When
the key is released, the choke will switch off
automatically.

 

EMU25911

 

Tiller handle

 

To change direction, move the tiller handle to
the left or right as necessary.

 

6. Throttle
7. Fully open

1. Neutral interlock trigger

 

1. Fully open
2. Fully closed

ZMU03160

Summary of Contents for F15D





























































































Reviews:

No comments