manualshive.com logo in svg

Yamaha F15D, Owner'S Manual, Page: 73 / 92

Share
Download
Yamaha F15D Owner'S Manual Download Page 73

 

Maintenance

 

68

 

shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTE:

 

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to

 

align it with the hole.

 

EMU29281

 

Changing gear oil

WARNING

 

EWM00800 

 

●

 

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

 

●

 

Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-

 

ly falls.

 

1.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the
gear case.

3.

Remove the gear oil drain screw.

NOTE:

 

If the magnetic gear oil drain screw
equipped: remove all metal particles from

 

the screw before installing it.

4.

Remove the oil level plug to allow the oil
to drain completely.

CAUTION:

 

ECM00710 

 

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-

 

pair of the lower unit seals.

NOTE:

 

For disposal of used oil consult your Yamaha

 

dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into

ZMU02063

 

1. Gear oil drain screw
2. Oil level plug

ZMU02064

2

1

Summary of Contents for F15D





























































































Reviews:

No comments