Yamaha F15D Owner'S Manual Download Page 53 | Manualshive

Page: 53 / 92

Yamaha F15D Owner'S Manual Download Page 53

48

Maintenance

EMU28216

Specifications

Dimension:

Overall length:

F15EH 1001 mm (39.4 in)
F15MH 1001 mm (39.4 in)
F15PH 1001 mm (39.4 in)
F15PR 643 mm (25.3 in)
F9.9ER 643 mm (25.3 in)
F9.9MH 1001 mm (39.4 in)
T9.9EH 1001 mm (39.4 in)
T9.9ER 643 mm (25.3 in)

Overall width:

F15EH 427 mm (16.8 in)
F15MH 427 mm (16.8 in)
F15PH 427 mm (16.8 in)
F15PR 369 mm (14.5 in)
F9.9ER 369 mm (14.5 in)
F9.9MH 427 mm (16.8 in)
T9.9EH 427 mm (16.8 in)
T9.9ER 369 mm (14.5 in)

Overall height S:

F15EH 1080 mm (42.5 in)
F15MH 1080 mm (42.5 in)
F9.9ER 1080 mm (42.5 in)
F9.9MH 1080 mm (42.5 in)

Overall height L:

F15EH 1207 mm (47.5 in)
F15MH 1207 mm (47.5 in)
F15PH 1207 mm (47.5 in)
F15PR 1207 mm (47.5 in)
F9.9ER 1207 mm (47.5 in)
F9.9MH 1207 mm (47.5 in)
T9.9EH 1253 mm (49.3 in)
T9.9ER 1253 mm (49.3 in)

Overall height X:

T9.9EH 1321 mm (52.0 in)

Transom height S:

F15EH 440 mm (17.3 in)
F15MH 440 mm (17.3 in)
F9.9ER 440 mm (17.3 in)

F9.9MH 440 mm (17.3 in)

Transom height L:

567 mm (22.3 in)

Transom height X:

T9.9EH 635 mm (25.0 in)

Weight (AL) S:

F15EH 48.0 kg (106 lb)
F15MH 45.0 kg (99 lb)
F9.9ER 47.0 kg (104 lb)
F9.9MH 45.0 kg (99 lb)

Weight (AL) L:

F15EH 50.0 kg (110 lb)
F15MH 47.0 kg (104 lb)
F15PH 55.0 kg (121 lb)
F15PR 54.0 kg (119 lb)
F9.9ER 49.0 kg (108 lb)
F9.9MH 47.0 kg (104 lb)
T9.9EH 51.0 kg (112 lb)
T9.9ER 50.0 kg (110 lb)

Weight (AL) X:

T9.9EH 52.0 kg (115 lb)

Performance:

Full throttle operating range:

4500–5500 r/min

Maximum output:

F15EH 11.0 kW@5000 r/min (15
HP@5000 r/min)
F15MH 11.0 kW@5000 r/min (15
HP@5000 r/min)
F15PH 11.0 kW@5000 r/min (15
HP@5000 r/min)
F15PR 11.0 kW@5000 r/min (15
HP@5000 r/min)
F9.9ER 7.3 kW@5000 r/min (10
HP@5000 r/min)
F9.9MH 7.3 kW@5000 r/min (10
HP@5000 r/min)
T9.9EH 7.3 kW@5000 r/min (10
HP@5000 r/min)
T9.9ER 7.3 kW@5000 r/min (10
HP@5000 r/min)

«
...
51
52
53
54
55
...
»

Summary of Contents for F15D





























































































Reviews:

No comments