manualshive.com logo in svg

Yamaha F15D, Owner'S Manual, Page: 61 / 92

Share
Download
Yamaha F15D Owner'S Manual Download Page 61

 

Maintenance

 

56

 

EMU28521

 

Maintenance chart

 

Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines. Refer to the sections in this chapter for
explanations of each owner-specific action.
The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

 

Item

Actions

Initial

Every

10 hours 

(1 month)

50 hours 

(3 

months)

100 

hours (6 
months)

200 

hours (1 

year)

 

Anode(s) (external)

Inspection / replace-
ment

Anode(s) (internal)

Inspection / replace-
ment

Battery

Inspection / charging

Cooling water pas-
sages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be dis-
assembled)

Inspection / cleaning

Fuel system

Inspection

Fuel tank (Yamaha por-
table tank)

Inspection / cleaning

Gear oil

Change

Greasing points

Greasing

Idling speed (carbure-
tor models)

Inspection / adjustment

Power trim and tilt unit

Inspection

Propeller and cotter pin

Inspection / replace-
ment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Throttle link / throttle 
cable / throttle pick-up 
timing

Inspection / adjustment

Water pump

Inspection

Engine oil

Inspection / change

Oil filter (cartridge)

Change

Summary of Contents for F15D





























































































Reviews:

No comments