Yamaha F15D Page 69 Owner'S Manual Download | Manualshive

Page: 69 / 92

background image

Maintenance

64

Then tighten 1/4 to 1/2 turn more. Tighten
the drain screw to the correct torque with a

torque wrench as soon as possible.

4.

Add the correct amount of oil through the
filler hole. Install the filler cap.

5.

Start the engine and watch to make sure
the low oil pressure warning indicator (if
equipped) turns off. Make sure that
there are no oil leaks.

CAUTION:

ECM00680

If the low oil pressure warning indicator
does not turn off or if there are oil leaks,
stop the engine and find the cause. Con-
tinued operation with a problem could
cause severe engine damage. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

6.

Turn off the engine and wait 3 minutes.
Recheck the oil level using the dipstick
to be sure the level falls between the up-
per and lower marks. Fill with oil if it is
below the lower mark, or drain to the
specified level if it is above the upper

mark.

7.

Dispose of used oil according to local
regulations.

NOTE:

●

For more information on the disposal of
used oil, consult your Yamaha dealer.

●

Change the oil more often when operating
the engine under adverse conditions such

as extended trolling.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

Recommended engine oil:

4-stroke outboard motor oil

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

ZMU02057

ZMU02058

ZMU02087

«
...
67
68
69
70
71
...
»

Summary of Contents for F15D





























































































Reviews:

No comments

Related manuals for F15D

Brand: ASROCK Pages: 198

Brand: Gigabyte Pages: 100

Brand: ECS Pages: 93

Brand: Texas Instruments Pages: 13

Brand: Biostar Pages: 51

Brand: Gigabyte Pages: 80

Brand: Hanasis Pages: 31

Brand: AOpen Pages: 8

Cypress S6SAP413A00SA1001

Brand: Infineon Technologies Pages: 33

Brand: Icop Pages: 30

Brand: Gigabyte Pages: 120

Brand: Texas Instruments Pages: 34

Brand: Asus Pages: 47

G31M-GS R2.0-QVL

Brand: ASROCK Pages: 2

Brand: Texas Instruments Pages: 17

Brand: Suzuki Pages: 92

Brand: DFI-ITOX Pages: 112

Brand: DFI-ITOX Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands