Yamaha F115D Owner'S Manual Download Page 61 | Manualshive

Page: 61 / 82

background image

Maintenance

56

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

6.

Activate the tilt-down switch until the trim
rods have retracted completely into the
cylinders.

7.

Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.

8.

Tilt the outboard motor down. Check
that the tilt rod and trim rods operate
smoothly.

NOTE:

Consult your Yamaha dealer if any operation

is abnormal.

EMU29171

Checking propeller

WARNING

EWM00321

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

●

Before inspecting, removing, or install-
ing the propeller, remove the spark
plug caps from the spark plugs. Also,
place the shift control in neutral, turn
the main switch to “

” (off) and re-

move the key, and remove the lanyard
from the engine stop switch. Turn off
the battery cut-off switch if your boat
has one.

●

Do not use your hand to hold the pro-
peller when loosening or tightening the
propeller nut. Put a wood block be-
tween the anti-cavitation plate and the
propeller to prevent the propeller from

turning.

2. Trim rods
3. Tilt support lever

1. Tilt support lever

1

ZMU02634

ZMU02635

ZMU04262

«
...
59
60
61
62
63
...
»

Summary of Contents for F115D



















































































Reviews:

No comments

Related manuals for F115D

Brand: Texas Instruments Pages: 16

STM32 Nucleo-32

Brand: ST Pages: 37

Brand: California Eastern Laboratories Pages: 34

EVB-LAN9252-SPI

Brand: Microchip Technology Pages: 22

BD93F10MWV-EVK-001

Brand: Rohm Pages: 20

Brand: Avalue Technology Pages: 83

Brand: DFI Pages: 121

Brand: AOpen Pages: 8

TS-7250 TS-72 Series

Brand: Technologic Systems Pages: 44

Brand: Technoland Pages: 74

Brand: BESTEK Pages: 8

Brand: Arrow Pages: 66

Brand: Arrow Pages: 74

Brand: Asus Pages: 64

Brand: Asus Pages: 64

Brand: Asus Pages: 66

Brand: Asus Pages: 64

Brand: Asus Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands