Yamaha F115D Owner'S Manual Download Page 54

Page: 54 / 82

Maintenance

NOTE:

When operating in salt water, turbid or muddy water, the engine should be flushed with clean

water after each use.

EMU28871

Maintenance chart (additional)

EMU28910

NOTE:

When using lead or high-sulfur gasoline, inspecting valve clearance may be required more

frequently than every 500 hours.

Throttle link / throttle
cable / throttle pick-up
timing

Inspection / adjustment

Water pump

Inspection

Engine oil

Inspection / change

Oil filter (cartridge)

Change

Spark plug(s)

Cleaning / adjustment /
replacement

Timing belt

Inspection / replace-
ment

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

months)

100

hours (6
months)

200

hours (1

year)

Item

Actions

Every

500 hours (2.5 years)

1000 hours (5 years)

Timing belt

Replacement

Valve clearance
(DOHC)

Inspection / adjustment

Summary of Contents for F115D



















































































Search results

Summary of Contents for F115D

Reviews:

Related manuals for F115D

Brands by name

Popular brands

Yamaha F115D, Owner'S Manual

Search results

Summary of Contents for F115D

Reviews:

Related manuals for F115D

Brands by name

Popular brands