Yamaha F115D Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 82

background image

Basic components

19

EMU26521

Low oil pressure warning indicator

If oil pressure drops too low, the warning in-
dicator will start to blink. For further informa-
tion, see page 26.

CAUTION:

ECM00020

●

Do not continue to run the engine if the
low oil pressure warning indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.

●

The low oil pressure warning indicator
does not indicate the engine oil level.
Use the oil dipstick to check the re-
maining oil quantity. For further infor-

mation, see page 30.

EMU26571

Overheat warning indicator

If the engine temperature rises too high, this

indicator will flash. For further information on
reading the indicator, see page 25.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see
page 25.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

1. Low oil pressure warning indicator

ZMU04754

ZMU01736

1

1. Overheat warning indicator

ZMU04715

ZMU01737

1

«
...
22
23
24
25
26
...
»

Summary of Contents for F115D



















































































Reviews:

No comments

Related manuals for F115D

Brand: Texas Instruments Pages: 30

Brand: Supermicro Pages: 90

DS-5116HFI Series

Brand: HIKVISION Pages: 22

Brand: JETWAY Pages: 19

Brand: Supermicro Pages: 100

Brand: Honda Pages: 152

Brand: Intel Pages: 36

Brand: ASROCK Pages: 244

Brand: Aura Light Pages: 8

Brand: Supermicro Pages: 125

Brand: Rohm Pages: 8

P4 Titan GA-8SIMLH-P

Brand: Gigabyte Pages: 104

Brand: Taiwan Commate Computer Inc. Pages: 31

Brand: TYAN Pages: 81

Brand: Fujitsu Pages: 32

Brand: Fujitsu Pages: 23

Brand: Fujitsu Pages: 40

Brand: Fujitsu Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands