background image

 

Operation

 

29

 

EMU26930

 

Mounting height (boat bottom)

 

To run your boat at optimum efficiency, the
water resistance (drag) of the boat and out-
board motor must be made as little as possi-
ble. The mounting height of the outboard
motor greatly affects the water resistance. If
the mounting height is too high, cavitation
tends to occur, thus reducing the propulsion;
and if the propeller tips cut the air, the engine
speed will rise abnormally and cause the en-
gine to overheat. If the mounting height is too
low, the water resistance will increase and
thereby reduce engine efficiency. Mount the
outboard motor so that the anti-cavitation
plate is in alignment with the bottom of the
boat.

NOTE:

 

 

The optimum mounting height of the out-

board motor is affected by the boat/motor
combination and the desired use. Test
runs at different heights can help deter-
mine the optimum mounting height. Con-
sult your Yamaha dealer or boat
manufacturer for further information on de-
termining the proper mounting height.

 

 

For instructions on setting the trim angle of

 

the outboard motor, see page 35.

 

EMU30172

 

Breaking in engine

 

Your new engine requires a period of break-
in to allow mating surfaces of moving parts to
wear in evenly. Correct break-in will help en-
sure proper performance and longer engine
life.

CAUTION:

 

ECM00800 

 

Failure to follow the break-in procedure
could result in reduced engine life or

 

even severe engine damage.

 

EMU27080

 

Procedure for 4-stroke models

 

Run the engine under load (in gear with a
propeller installed) as follows.
1.

For the first hour of operation:
Run the engine at 2000 r/min or at ap-
proximately half throttle.

2.

For the second hour of operation:
Run the engine at 3000 r/min or at ap-
proximately three-quarter throttle.

3.

For the next eight hours of operation:
Avoid continuous operation at full throt-
tle for more than five minutes at a time.

4.

After the first 10 hours:
Operate the engine normally.

 

EMU27101

 

Preoperation checks

WARNING

 

EWM00080 

 

If any item in the preoperation check is

 

1. Center line (keel line)

ZMU01874

Summary of Contents for F115D



















































































Reviews: