Yamaha F115D Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 82

background image

Operation

36

the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the

trim angle.

EMU27881

Adjusting trim angle

Power trim and tilt models

WARNING

EWM00750

●

Be sure all people are clear of the out-
board motor when adjusting the tilt an-
gle, also be careful not to pinch any
body parts between the drive unit and
clamp bracket.

●

Use caution when trying a trim position
for the first time. Increase speed gradu-
ally and watch for any signs of instabil-
ity or control problems. Improper trim
angle can cause loss of control.

●

Use the power tilt switch located on the

bottom engine cowling (if equipped)
only when the boat is at a complete

stop with the engine off.

Adjust the outboard motor trim angle using
the power trim and tilt switch.

1. Trim operating angle

1

ZMU04258

1. Power trim and tilt switch

1. Power trim and tilt switch

1. Power trim and tilt switch

ZMU04601

DN

UP

1

UP

DN

1

ZMU04231

«
...
39
40
41
42
43
...
»

Summary of Contents for F115D



















































































Reviews:

No comments

Related manuals for F115D

Brand: QDI Pages: 69

Brand: Biostar Pages: 27

Brand: Biostar Pages: 54

PCM-8152 3rd Generation

Brand: Aaeon Pages: 6

conga-HPC/EVAL-Server

Brand: Congatec Pages: 54

Tiger MPX S2466

Brand: TYAN Pages: 1

Brand: Watski Pages: 43

Brand: Mercury Pages: 102

Brand: ASROCK Pages: 56

Brand: Gigabyte Pages: 96

Brand: ON Semiconductor Pages: 22

ConnectCore 6UL SBC Pro

Brand: Digi Pages: 54

Brand: Zeal-All Pages: 8

P5B PRO - QUICK

Brand: ASROCK Pages: 48

Brand: unicore Pages: 11

P67 PROFESSIONAL

Brand: ASROCK Pages: 9

Brand: Abit Pages: 134

Brand: Asus Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands