Yamaha F115D Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 82

background image

Operation

39

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

ZMU04602

UP

UP

ZMU04232

ZMU03449

ZMU03452

«
...
42
43
44
45
46
...
»

Summary of Contents for F115D



















































































Reviews:

No comments

Related manuals for F115D

Brand: Qorvo Pages: 8

Brand: Texas Instruments Pages: 52

Brand: Intertec Components Pages: 3

Analog Devices DC2605A

Brand: Linear Pages: 16

970 Extreme3 R2.0

Brand: ASROCK Pages: 70

Brand: Texas Instruments Pages: 25

Brand: JS Automation Pages: 18

Brand: DFI Pages: 92

Brand: ALi Confidential Pages: 24

Brand: Micronics Pages: 80

755FXK8AA series

Brand: Foxconn Pages: 87

Brand: NXP Semiconductors Pages: 138

Brand: ASROCK Pages: 39

MOTORKIT-91F267-MC

Brand: Fujitsu Pages: 33

Brand: Fujitsu Pages: 30

Brand: Fujitsu Pages: 16

Brand: Fujitsu Pages: 14

Brand: Fujitsu Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands