Yamaha EF7000 Service Manual Download Page 140

Page: 140 / 178

6-5

TRBL

ENGINE

ENGINE SPEED DOES NOT INCREASE

Remove the electric
equipment with too
much wattage.

Check if the electric equipment consumes too
much wattage for this generator.

GOOD

TOO MUCH

Decarbonize the com-
bustion chamber if there
is carbon deposits.

Check the compression pressure.

GOOD

TOO HIGH

TOO LOW

Clean.

Check the air filter element for dirt.

GOOD

DIRTY

Clean, adjust, or replace.

Check the spark plug for dirt and check the spark
plug gap.

GOOD

DIRTY OR OUT OF

SPECIFICATION

Adjust.

Measure the valve clearance.

GOOD

OUT OF

SPECIFICATION

Resurface or
replace.

Check the valve face and valve seat for wear.

GOOD

WORN

Correct.

Check if the marks on the crankshaft and cam-
shaft are aligned.

GOOD

NOT GOOD

Rebore or
replace.

Check if there is seizure, wear, or damage on the
piston, piston ring, or cylinder.

GOOD

SEIZURE OR WORN

Summary of Contents for EF7000



















































































































































































Search results

Summary of Contents for EF7000

Reviews:

Related manuals for EF7000

Brands by name

Popular brands

Yamaha EF7000, Service Manual

Search results

Summary of Contents for EF7000

Reviews:

Related manuals for EF7000

Brands by name

Popular brands