Yamaha Diver 510N F XJ6F Owner'S Manual Download | Manualshive

Page: 28 / 102

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-14

3

EAU26823

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a
brake lever position adjusting dial. To
adjust the distance between the brake
lever and the handlebar grip, turn the
adjusting dial while holding the lever
pushed away from the handlebar grip.
Make sure that the appropriate setting
on the adjusting dial is aligned with
the “

” mark on the brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU47521

ABS (for ABS models)

The Yamaha ABS (Anti-lock Brake
System) features a dual electronic con-
trol system, which acts on the front and
rear brakes independently. The ABS is
monitored by an ECU, which will have
recourse to manual braking if a mal-
function occurs.

WARNING

EWA10090

●

The ABS performs best on long
braking distances.

●

On certain (rough or gravel)
roads, the braking distance may
be longer with than without the
ABS. Therefore, always keep a
sufficient distance to the vehicle
ahead to match the riding
speed.

TIP

●

The ABS performs a self-diagno-
sis test for a few seconds each
time the vehicle first starts off after
the key was turned to “ON”. During
this test, a “clicking” noise can be
heard from under the seat, and if
the brake lever or brake pedal are

1. Brake lever

2. Brake lever position adjusting dial

3. “

” mark

4. Distance between brake lever and handlebar

grip

1. Brake pedal

1

U1CWE0E0.book Page 14 Friday, September 11, 2009 9:05 AM

«
...
26
27
28
29
30
...
»

Summary of Contents for Diver 510N F XJ6F







































































































Reviews:

No comments

Related manuals for Diver 510N F XJ6F

Brand: GBRacing Pages: 2

Brand: VIKING BAGS Pages: 2

Brand: hepco & becker Pages: 3

Brand: SUOMY Pages: 84

Brand: Touratech Pages: 4

Brand: paladin Pages: 2

Brand: hepco & becker Pages: 5

Brand: Tool it Pages: 26

Brand: Leatt Pages: 26

Brand: Leatt Pages: 26

Brand: RADE/GARAGE Pages: 6

Brand: Janus Pages: 96

390 Duke AR 2018

Brand: KTM Pages: 22

Brand: KTM Pages: 12

Brand: R&G Pages: 3

Brand: Power Riders Pages: 5

Brand: HealTech Electronics Pages: 4

Brand: Fantic Motor Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands