Yamaha Diver 510N F XJ6F Owner'S Manual Download

Page: 94 / 102

SPECIFICATIONS

8-1

Dimensions:

Overall length:

2120 mm (83.5 in)

Overall width:

770 mm (30.3 in)

Overall height:

1185 mm (46.7 in)

Seat height:

785 mm (30.9 in)

Wheelbase:

1440 mm (56.7 in)

Ground clearance:

140 mm (5.51 in)

Minimum turning radius:

2800 mm (110.2 in)

Weight:

With oil and fuel:

XJ6F 215 kg (474 lb)
XJ6FA 220 kg (485 lb)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Forward-inclined parallel 4-cylinder

Displacement:

600 cm³

Bore

stroke:

65.5

44.5 mm (2.58

1.75 in)

Compression ratio:

12.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

Type:

SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter cartridge replacement:

2.50 L (2.64 US qt, 2.20 Imp.qt)

With oil filter cartridge replacement:

2.80 L (2.96 US qt, 2.46 Imp.qt)

Cooling system:

Coolant reservoir capacity (up to the
maximum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

Radiator capacity (including all routes):

2.00 L (2.11 US qt, 1.76 Imp.qt)

Air filter:

Air filter element:

Oil-coated paper element

Fuel:

Recommended fuel:

Regular unleaded gasoline only

Fuel tank capacity:

17.3 L (4.57 US gal, 3.81 Imp.gal)

Fuel reserve amount:

3.2 L (0.85 US gal, 0.70 Imp.gal)

Fuel injection:

Throttle body:

ID mark:

XJ6F 20S1 00
XJ6F 20S2 10
XJ6FA 20S1 00

Spark plug (s):

Manufacturer/model:

NGK/CR9E

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

86/44 (1.955)

Secondary reduction system:

Chain drive

Secondary reduction ratio:

46/16 (2.875)

Transmission type:

Constant mesh 6-speed

Operation:

Left foot operation

–20 –10 0

10 20 30 40 50 ˚C

10 30 50 70 90 110

130 ˚F

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

SAE 10W-50

U1CWE0E0.book Page 1 Friday, September 11, 2009 9:05 AM

Summary of Contents for Diver 510N F XJ6F







































































































Search results

Summary of Contents for Diver 510N F XJ6F

Reviews:

Related manuals for Diver 510N F XJ6F

Brands by name

Popular brands

Yamaha Diver 510N F XJ6F, Owner'S Manual

Search results

Summary of Contents for Diver 510N F XJ6F

Reviews:

Related manuals for Diver 510N F XJ6F

Brands by name

Popular brands