Yamaha Diver 510N F XJ6F Page 18 Owner'S Manual Download | Manualshive

Page: 18 / 102

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-4

3

EAU11004

Indicator and warning lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

”

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection

circuit, the following cycle will be
repeated until the malfunction is
corrected: The oil level warning
light will flash ten times, then go off
for 2.5 seconds. If this occurs,
have a Yamaha dealer check the
vehicle.

EAU11427

Coolant temperature warning
light “

”

This warning light comes on if the en-
gine overheats. If this occurs, stop the
engine immediately and allow the en-
gine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

NOTICE

ECA10021

Do not continue to operate the en-
gine if it is overheating.

1. Turn signal indicator light “

”

2. Immobilizer system indicator light

3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Engine trouble warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

8. Anti-lock Brake System (ABS) warning

light “

” (for ABS models)

1

2

3 4 5

7 6

8

ABS

U1CWE0E0.book Page 4 Friday, September 11, 2009 9:05 AM

«
...
16
17
18
19
20
...
»

Summary of Contents for Diver 510N F XJ6F







































































































Reviews:

No comments

Related manuals for Diver 510N F XJ6F

Brand: X-lite Pages: 136

Brand: Jialing Honda Pages: 10

Bonneville T100

Brand: Triumph Pages: 198

Brand: Honda Pages: 140

Windscreen N20012A

Brand: VStreamT Pages: 3

Brand: DYNATEK Pages: 5

Brand: Yamasaki Pages: 28

Brand: tucanourbano Pages: 4

Brand: Smarter tools Pages: 28

Brand: Derbi Pages: 179

Brand: R&G Pages: 6

Brand: R&G Pages: 12

SPYDER F3TM 2016

Brand: Can-Am Pages: 171

Brand: Shark Pages: 20

Brand: tucanourbano Pages: 4

Brand: Cagiva Pages: 142

Brand: Kinroad Pages: 27

Brand: hepco & becker Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands