Yamaha Diver 510N F XJ6F Owner'S Manual Download

Page: 34 / 102

INSTRUMENT AND CONTROL FUNCTIONS

3-20

EAU14452

Storage compartment

The storage compartment is located
under the seat. (See page 3-18.)

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of XJ6F 185 kg (408 lb)
XJ6FA 180 kg (397 lb) for the ve-
hicle.

When storing the Owner’s Manual or
other documents in the storage com-
partment, be sure to wrap them in a
plastic bag so that they will not get wet.

When washing the vehicle, be careful
not to let any water enter the storage
compartment.

EAU46830

Handlebar position

The handlebars can be adjusted to one
of two positions to suit the rider’s pref-
erence. Have a Yamaha dealer adjust
the position of the handlebars.

1. Storage compartment

1. Handlebar

U1CWE0E0.book Page 20 Friday, September 11, 2009 9:05 AM

Summary of Contents for Diver 510N F XJ6F







































































































Search results

Summary of Contents for Diver 510N F XJ6F

Reviews:

Related manuals for Diver 510N F XJ6F

Brands by name

Popular brands

Yamaha Diver 510N F XJ6F, Owner'S Manual

Search results

Summary of Contents for Diver 510N F XJ6F

Reviews:

Related manuals for Diver 510N F XJ6F

Brands by name

Popular brands