Yamaha 8C Owner'S Manual Download | Manualshive

Page: 74 / 94

background image

5-1

E

EMU01663¯

TROUBLESHOOTING

A problem in the fuel, compression, or ignition systems can cause poor starting, loss of
power, or other problems. The troubleshooting chart describes basic checks and possi-
ble remedies. (This chart covers all Yamaha outboard motors. Therefore, some items
may not apply to your model.)
If your outboard motor requires repair, bring it to a Yamaha dealer.
If the engine warning indicator is flashing, consult your Yamaha dealer.

A. Starter will not

operate.

Trouble

Possible Cause

Remedy

1. Starter components faulty.

2. Shift lever in gear.

1. Have serviced by a Yamaha

dealer.

2. Shift to neutral.

B. Engine will not

start (Starter

operates).

1. Fuel tank empty.

2. Fuel contaminated or stale.

3. Fuel filter clogged.

4. Starting procedure incorrect.

5. Fuel pump malfunctions.

6. Spark plug(s) fouled or incorrect

type.

7. Spark plug cap(s) fitted incorrectly.

8. Poor connections or damaged

ignition wiring.

9. Ignition parts faulty.

10. Engine stop switch lanyard not

attached.

11. Engine inner parts damaged.

1. Fill tank with clean, fresh fuel.

2. Fill tank with clean, fresh fuel.

3. Clean or replace filter.

4. Read “STARTING ENGINE”

section.

5. Have serviced by a Yamaha

dealer.

6. Inspect spark plug(s). Clean or

replace with recommended type.

7. Check and re-fit cap(s).

8. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

9. Have serviced by a Yamaha

dealer.

10. Attach lanyard.

11. Have serviced by a Yamaha

dealer.

6M8-F9-17-5 2/4/03 9:49 AM Page 2

«
...
72
73
74
75
76
...
»

Summary of Contents for 8C































































































Reviews:

No comments

Related manuals for 8C

Vanguard Diesel 432447

Brand: Briggs & Stratton Pages: 24

Sonesse Ultra 50 DC RS485

Brand: SOMFY Pages: 16

Brand: SCREENLINE Pages: 4

Brand: FUTABA Pages: 3

Brand: Volvo Penta Pages: 64

Brand: Volvo Penta Pages: 104

Brand: TCF Pages: 16

Brand: Toro Pages: 27

Brand: O.S. engine Pages: 18

Revenge CTM Series

Brand: Absima Pages: 3

Brand: VM Pages: 108

Brand: HIOTH TECHNOLOGY Pages: 5

Brand: AUSTRALIAN MADE Pages: 20

Brand: Baumuller Pages: 25

Brand: Barrus Pages: 88

Brand: DLE Pages: 4

Brand: LinMot Pages: 39

Brand: Tecno Automazione Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands