Yamaha 8C Owner'S Manual Download

Page: 35 / 94

3-8

EMF43010

Controls

Check throttle, shift, and steering for
proper operation before starting the
engine.

The controls should work smoothly,
without binding or unusual free play.

Look for loose or damaged connec-
tions.

Check operation of the starter and stop
switches when the outboard motor is in
the water.

EMF43510

Engine

Check the engine and engine mounting.

Look for loose or damaged fasteners.

Check the propeller for damage.

Do not start the engine out of water.
Overheating and serious engine damage
can occur.

EMF50012

BREAKING IN (RUNNING IN)

ENGINE

Your new engine requires a period of
break-in (running-in) to allow mating sur-
faces of moving parts to wear-in evenly.
Correct break-in (running-in) will help
ensure proper performance and longer
engine life.

Failure to follow the break-in (running-in)
procedure may result in reduced engine
life or even severe engine damage.

6M8-F9-17-3 2/4/03 9:51 AM Page 9

Summary of Contents for 8C































































































Search results

Summary of Contents for 8C

Reviews:

Related manuals for 8C

Brands by name

Popular brands

Yamaha 8C, Owner'S Manual

Search results

Summary of Contents for 8C

Reviews:

Related manuals for 8C

Brands by name

Popular brands