Yamaha 8C Owner'S Manual Download | Manualshive

Page: 81 / 94

background image

5-8

E

107012

107013

107014

EMN50011

TREATMENT OF SUBMERGED
MOTOR

If the outboard motor is submerged,
immediately take it a Yamaha dealer.
Otherwise, some corrosion may begin
almost immediately. If you cannot imme-
diately take the outboard motor to a
Yamaha dealer, follow the procedure bel-
low for taking care to minimize engine
damage.

1)

Thoroughly wash away mud, salt,
seaweed, etc. with fresh water.

2)

Remove the spark plugs and face the
spark plug holes downward to allow
any water, mud or contaminants to
drain.

3)

Drain the fuel from the carburetor.

4)

Feed fogging oil or engine oil through
the carburetors and spark plug holes
while cranking with the manual
starter or emergency starter rope.

5)

Take the outboard motor to a Yamaha
dealer as soon as possible.

c

C

Do not attempt to run the motor until it
has been completely inspected.

6M8-F9-17-5 2/4/03 9:49 AM Page 9

«
...
79
80
81
82
83
...
»

Summary of Contents for 8C































































































Reviews:

No comments

Related manuals for 8C

Brand: Mercedes-Benz Pages: 940

Brand: ABB Pages: 215

Brand: Northern Lights Pages: 36

Brand: Northern Lights Pages: 45

Brand: Northern Lights Pages: 56

Brand: RADEMACHER Pages: 72

Brand: Masport Pages: 14

Brand: FIAMA Pages: 7

Brand: Magnum Pages: 7

Brand: Detroit Diesel Pages: 42

Brand: Champion Pages: 22

Brand: Honda Pages: 5

Brand: Honda Pages: 16

Shire 15 Work Boat YM

Brand: Barrus Pages: 44

130000 950 Series

Brand: Briggs & Stratton Pages: 100

Brand: Wood-mizer Pages: 192

Brand: Roto Pages: 8

Brand: M.T.H. Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands