Yamaha 8C Owner'S Manual Download

Page: 62 / 94

4-11

207015*

EMM52010

INSPECTING AND REPLACING FUEL
FILTER

Gasoline (petrol) is highly flammable, and
its vapors are flammable and explosive.

If you have any question about properly
doing the procedure, consult your
Yamaha dealer.

Do not perform the procedure on a hot
or running engine. Allow the engine to
cool.

There will be fuel in the fuel filter.
Keep away from sparks, cigarettes,
flames or other sources of ignition.

The procedure will allow some fuel to
spill.
Catch fuel in a rag. Wipe up any spilled
fuel immediately.

Improper replacement can result in a
fuel leak, which could result in a fire or
explosion hazard.

Check the fuel filter periodically.
The fuel filter is a one-piece, disposable
type. If foreign matter is found in the fil-
ter, replace it. For replacement of the fuel
filter, consult a Yamaha dealer.

6M8-F9-17-4 2/4/03 9:50 AM Page 12

Summary of Contents for 8C































































































Search results

Summary of Contents for 8C

Reviews:

Related manuals for 8C

Brands by name

Popular brands

Yamaha 8C, Owner'S Manual

Search results

Summary of Contents for 8C

Reviews:

Related manuals for 8C

Brands by name

Popular brands