Yamaha 2010 XVS1300AZ Owner'S Manual Download | Manualshive

Page: 20 / 92

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-4

4

EAU11004

Indicator and warning lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

”

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection

circuit, the following cycle will be
repeated until the malfunction is
corrected: The oil level warning
light will flash ten times, then go off
for 2.5 seconds. If this occurs,
have a Yamaha dealer check the
vehicle.

EAU42744

Fuel level warning light “

”

This warning light comes on when the
fuel level drops below approximately
3.7 L (0.98 US gal, 0.81 Imp.gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

The vehicle must be on a level sur-
face and positioned upright, other-
wise the fuel level warning light
may not come on and go off at the
appropriate times.

1. Neutral indicator light “

”

2. Coolant temperature warning light “

”

3. Engine trouble warning light “

”

4. High beam indicator light “

”

5. Turn signal indicator light “

”

6. Oil level warning light “

”

7. Fuel level warning light “

”

8. Immobilizer system indicator light

U12C23E0.book Page 4 Tuesday, October 20, 2009 4:17 PM

«
...
18
19
20
21
22
...
»

Summary of Contents for 2010 XVS1300AZ





























































































Reviews:

No comments

Related manuals for 2010 XVS1300AZ

Brand: Razor Pages: 2

Brand: Graphite Pages: 44

Premium Motorcycle Cover

Brand: Velmia Pages: 32

Brand: GAS GAS Pages: 32

Brand: Suzuki Pages: 89

Brand: X-lite Pages: 96

Brand: Yamaha Pages: 276

Brand: Hudora Pages: 8

Brand: Faller Pages: 8

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 63

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 94

Star XV1900AE 2013

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands