Yamaha 2010 XVS1300AZ Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 92

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-17

7

decrease the clutch lever free play,
turn the adjusting bolt in direction
(b).

TIP

If the specified clutch lever free play
could be obtained as described above,
skip steps 4–7.

4. Fully turn the adjusting bolt in di-

rection (a) to loosen the clutch ca-
ble.

5. Loosen the locknut further down

the clutch cable.

6. To increase the clutch lever free

play, turn the clutch lever free play
adjusting nut in direction (a). To

decrease the clutch lever free play,
turn the adjusting nut in direction
(b).

7. Tighten the locknut at the clutch

cable.

8. Tighten the locknut at the clutch le-

ver, and then slide the rubber cov-
er to its original position.

EAU37913

Checking the brake lever free
play

There should be no free play at the
brake lever end. If there is free play,
have a Yamaha dealer inspect the
brake system.

WARNING

EWA14211

A soft or spongy feeling in the brake
lever can indicate the presence of air
in the hydraulic system. If there is air
in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the

1. Clutch lever free play adjusting nut (clutch

cable)

2. Locknut (clutch cable)

1

2

(a)

(b)

1. No brake lever free play

1

U12C23E0.book Page 17 Tuesday, October 20, 2009 4:17 PM

«
...
57
58
59
60
61
...
»

Summary of Contents for 2010 XVS1300AZ





























































































Reviews:

No comments

Related manuals for 2010 XVS1300AZ

Brand: KAYO MOTOR Pages: 84

Stelvio 1200 MY11 2011

Brand: MOTO GUZZI Pages: 385

LOCK-IT 506007-7

Brand: hepco & becker Pages: 2

ZIEGER 10005243

Brand: IBEX Pages: 4

Brand: hepco & becker Pages: 3

Brand: MZ Pages: 82

Brand: R&G Pages: 6

Brand: R&G Pages: 12

Brand: tucanourbano Pages: 4

VarioProtect PANORAMA-W R-TC

Brand: Schweißkraft Pages: 22

Brand: Beta Pages: 38

Brand: Beta Pages: 79

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 230

CRF1000 Africa Twin

Brand: Honda Pages: 375

RetroRadio BT100

Brand: Biketronics Pages: 2

Brand: KTM Pages: 26

Brand: Honda Pages: 384

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands