background image

ABS (ANTI-LOCK BRAKE SYSTEM)

8-87

2. Check that the main switch coupler is securely connected.
3. Check that the meter assembly coupler is securely connected. (Refer to "ABS CONNECTOR 

LOCATION CHART" on page 8-75.)
When these checks are finished, return to [A] and check the ABS again.

EAS4S81024

[C-3] ABS WARNING LIGHT FLASHES

1. When the warning light flashes “ON” for 0.25 seconds and “OFF” for 0.75 seconds, check the 

stop switch or 3-4), 5).

2. When the warning light flashes “ON” for 0.75 seconds and “OFF” for 0.25 seconds, the starter 

motor monitor is defective. Same as the error code 22 or 3-1), 2), 3).

3. When the warning light flashes “ON” for 1 second and “OFF” for 1 second, it is another malfunc-

tion. Same as the error code 28.
The following are probable causes to explain why the ABS warning light flashed while riding and 
then stopped flashing or stopped flashing when main switch was set “OFF” to “ON”.
1. The rear wheel was rotated with the vehicle on the centerstand. 

 The system is normal.

2. The rear wheel was raced. 

 The system is normal.

3. The vehicle was ridden on the rear wheel with the front wheel elevated. 

 The system is nor-

mal.

4. The vehicle was ridden on extremely uneven roads continuously. 

 The system is normal.

5. The brake switch is defective or improperly adjusted. 

 Replace or adjust.

EAS4S81025

[C-4] ABS WARNING LIGHT FLASHES EVERY 0.5 SECOND

If the ABS warning light flashes every 0.5 second, the malfunction code of a past malfunction has 
not been stored in the memory of the ABS ECU. If a malfunction code is displayed on the multifunc-
tion display, the ABS warning light flashes. Make sure that the customer understands the possible 
conditions when the ABS warning light comes on.
1. Voltage drop

For the ABS to operate correctly, the voltage should be always higher than the specified voltage. 
If the voltage drops to lower than 10 V, the ABS warning light comes on and the ABS does not 
operate. When the voltage recovers to higher than 10 V, the ABS operates. However, the mag-
neto, battery and rectifier/regulator must be checked. Follow the regular procedures for service 
of the power supply system.

2. ABS is stopped by the ABS ECU

The ABS ECU may stop the ABS operation if it is exposed to extremely strong electromagnetic 
waves or static electricity.
When the ABS ECU is no longer exposed to the electromagnetic waves, static electricity, and the 
ABS warning light is not flashing, there is no effect on the operation of the ABS. Explain to the 
customer that the ABS will operate normally.

EAS27880

[C-5] DIAGNOSIS BY THE MALFUNCTION CODE

Malfunction codes are used to determine the malfunctions that have occurred. (Refer to “[B-4] MAL-
FUNCTION CHECK BY THE ABS SELF-DIAGNOSIS (PAST MALFUNCTION)” and “[B-5] MAL-
FUNCTION CHECK BY THE ABS SELF-DIAGNOSIS (PRESENT MALFUNCTION)”.) The 
malfunction codes are explained in the following table.

NOTE:

Record all of the malfunction codes displayed and check the check points.

Summary of Contents for 2007 FZ6-NA



























































































































































































































































































































































































































































































































































Reviews: