Yamaha 2006 FZ1-N Service Manual Download Page 107 | Manualshive

Page: 107 / 451

background image

CHASSIS

3-22

EAS21140

CHASSIS

EAS21160

ADJUSTING THE FRONT DISC BRAKE

1. Adjust:

• Brake lever position

(distance “a” from the throttle grip to the
brake lever)

NOTE:

• While pushing the brake lever forward, turn

the adjusting dial “1” until the brake lever is in
the desired position.

• Be sure to align the setting on the adjusting

dial with the arrow mark “2” on the brake
lever holder.

WARNING

EWA13060

• After adjusting the brake lever position,

make sure the pin on the brake lever
holder is firmly inserted in the hole in the
adjusting dial.

• A soft or spongy feeling in the brake lever

can indicate the presence of air in the
brake system. Before the vehicle is oper-
ated, the air must be removed by bleeding
the brake system. Air in the brake system
will considerably reduce in loss of control
and possibly an accident. Therefore,
check and if necessary, bleed the brake
system.

CAUTION:

ECA13490

After adjusting the brake lever position,
make sure there is no brake drag.

EAS21190

ADJUSTING THE REAR DISC BRAKE

1. Adjust:

• Brake pedal position

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or

“b” until the specified brake pedal position
is obtained.

WARNING

EWA13070

After adjusting the brake pedal position,
check that the end of the adjusting bolt “c”
is visible through the hole “d”.

c. Tighten the locknut “1” to specification.

WARNING

EWA13050

A soft or spongy feeling in the brake pedal
can indicate the presence of air in the brake
system. Before the vehicle is operated, the
air must be removed by bleeding the brake
system. Air in the brake system will consid-
erably reduce braking performance.

CAUTION:

ECA13510

After adjusting the brake pedal position,
make sure there is no brake drag.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Adjust:

• Rear brake light switch

Refer to "ADJUSTING THE REAR BRAKE
LIGHT SWITCH" on page 3-24.

Direction “b”

Distance “a” is the largest.

Direction “c”

Distance “a” is the smallest.

Direction “a”

Brake pedal is raised.

Direction “b”

Brake pedal is lowered.

Locknut

18 Nm (1.8 m·kg, 13 ft·lb)

«
...
105
106
107
108
109
...
»

Summary of Contents for 2006 FZ1-N




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 FZ1-N

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Brand: Crivit Pages: 70

COMFORT 10130810

Brand: Contracor Pages: 36

Brand: KEEWAY Pages: 15

Brand: DAELIM Pages: 93

640 LC4 ENDURO 2006

Brand: KTM Pages: 60

Two Fifty 250 cc

Brand: Mash Pages: 62

Brand: R&G Pages: 9

690 Enduro R 2019

Brand: KTM Pages: 274

Brand: Zontes Pages: 119

Brand: CRATONI Pages: 61

TRACER MTT9K 2019

Brand: Yamaha Pages: 122

TT-R125(N) 2000

Brand: Yamaha Pages: 508

TT-R125(R) 2002

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 610

TT-R125(S) 2003

Brand: Yamaha Pages: 610

Brand: Yamaha Pages: 616

Brand: Yamaha Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands