background image

11

Other functions

As depends on the terms of use condition and what kind of label you use,
additional adjustments will be necessary as follows.

In the case that label (backing paper) setting slants (illustration 1)

Make some adjustments with Label Holder.

 ・

If label slants in left side, tighten the screw.

 ・

If label slants in right side, loosen the screw.

In the case that label doesn't remove well at Removal Plate (illustration 2)

Make some adjustments with Label Holder Tension Adjust Screw as shown

    on illustration 2.

 ・

Make sure whether it will work properly after turning one screw

     adjusutment.

 ・

Adjust the screw until label is removed definitely at Removal Plate.

 ・

If label is not removed properly even though screw adjustment is done

     to the end, please don't use the machine and contact the supplier.

In the case that label is wound loose or label is not wound (illustration 3)

Turn Backing Paper Release Bar in the direction as shown on the

    illustration 3 while pressing Tension Adjust Button.

 ・

Make sure that it will work properly after making a half turn of Tension

      Adjust Button.

 ・

Make an adjustment until label winds into Backing Paper Release Bar.

Notice: Please don't turn counterclockwise as shown on the illustration 3.

In the case that label is not detected (illustration 4-5)

Move the sensor to the proper position by left and right as detects the

    label.

Make some adjustment with Sensor Angle Adjust Screw to place in the

    middle of the label that stops at Removal Plate.

In the case of checking the sensibility of the sensor (illustration 4-5)

Please follow the instructions for the correct use.

Turn the switch off after label stopping under the sensor.

Turn the switch on while pressing START BUTTON.

 ・

Release START BUTTON after the sound of the peep.

 ・

Display the number from 0 to 100.

 ・

The sensibility of the sensor will be better as much as the number

     increased.

Place the best position for the sensor by moving to left and right and by

    changing the angle.

Press START BUTTON longer time and revert to the mode as you use.

1

2

3

4

5

T

I

G

H

T

LOOSE

P

O

E

N

Summary of Contents for LDX-60

















Reviews: