Yaesu FTDX-9000MP, Operation Manual

Page: 154 / 180

Page 152 FT
DX
9000MP O
PERATION
M
ANUAL
MMMMM
ENU ENU
ENU ENU
ENU
M M M M M
ODE ODE
ODE ODE
ODE
MODE-CW G
ROUP
048. F-KEYER TYPE
Function : Selects the desired keyer operation mode
for the device connected to the front panel’s KEY jack.
Available Values : OFF/BUG/ELEKEY/ACS
Default Setting : ELEKEY
OFF: Disables the front panel’s keyer (“straight
key” mode for use with external keyer or
computer-driven keying interface).
BUG: Mechanical “bug” keyer emulation. One
paddle produces “dits” automatically, while
the other paddle manually produces “dahs.”
ELEKEY: Iambic keyer with ACS (Automatic Char-
acter Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
049. F-CW KEYER
Function : Selects the keyer paddle’s wiring configu-
ration of the KEY jack on the front panel.
Available Values : NOR/REV
Default Setting : NOR
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground
050. R-KEYER TYPE
Function : Select the desired keyer operation mode
for the device connected to the rear panel’s KEY jack.
Available Values : OFF/BUG/ELEKEY/ACS
Default Setting : ELEKEY
OFF: Disables the front panel’s keyer (“straight
key” mode for use with external keyer or
computer-driven keying interface).
BUG: Mechanical “bug” keyer emulation. One
paddle produces “dits” automatically, while
the other paddle manually produces “dahs.”
ELEKEY: Iambic keyer with ACS (Automatic Char-
acter Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
051. R-CW KEYER
Function : Selects the keyer paddle’s wiring configu-
ration of the KEY jack on the rear panel.
Available Values : NOR/REV
Default Setting : NOR
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground
052. CW AUTO MODE
Function : Enables/disables CW keying while oper-
ating on SSB.
Available Values : OFF/50MHz/ON
Default Setting : OFF
OFF: Disables CW keying while operating on
SSB.
50MHz: Enables CW keying only while operating
SSB on 50 MHz (but not HF).
ON: Enables CW keying while operating on SSB
(all TX bands).
Note : This feature allows you to move someone from
SSB to CW without having to change modes on the
front panel.
053. CW BFO
Function : Sets the CW carrier oscillator injection side
for the CW mode.
Available Values : USB/LSB/AUTO
Default Setting : USB
USB: Injects the CW carrier oscillator on the USB
side.
LSB: Injects the CW carrier oscillator on the LSB
side.
AUTO: Injects the CW carrier oscillator on the LSB
side while operating on the 7 MHz band and
below, and the USB side while operating on
the 10 MHz band and up.
054. CW BK-IN
Function : Sets the CW “break-in” mode.
Available Values : SEMI/FULL
Default Setting : SEMI
SEMI: The transceiver will operate in the semi break-
in mode. The delay (receiver recovery) time
is set by the front panel’s [
CW DELAY
] knob.
FULL: The transceiver will operate in the full break-
in (QSK) mode.
055. CW WAVE SHAPE
Function : Selects the CW carrier wave-form shape
(rise/fall times).
Available Values : 1/2/4/6 msec
Default Setting : 4 msec
056. CW WEIGHT
Function : Sets the Dot:Dash ratio for the built-in elec-
tronic keyer.
Available Values : (1:) 2.5 ~ 4.5
Default Setting : 3.0