background image

Heat / Cooling Meters Calculator Unit  
PolluTherm can be combined with PolluFlow 
Installation and Operating Instructions 

 

 

MH 6114 INT PolluTherm, Page 3 

 

2. Safety Notes

 

 

 
 

  Installation of the PolluTherm requires 

specialist knowledge and should only be 
carried out by a person trained for this. 

  The PolluTherm must be used within the 

conditions outlined in Section1.  

  During installation of the PolluTherm, make 

sure that the sleeve or ball valve is correctly 
installed, otherwise there is a danger of 
scalding due to escaping heating medium. 
Therefore, during removal, first close the 
shut-off valves. 

  The brass threads can have sharp edges due 

to the production method. Therefore, we 
recommend to use protective gloves. 

  Heat and cooling meters are measurement 

devices and must be handled with care. In 
order to protect from damage and 
contamination, they should only be removed 
from the packaging before installation. 

  If the housing and/or connecting cable shows 

any signs of damage, the device must be 
taken out of operation and secured to prevent 
further operation. 

  For cleaning, only use a Water moistened 

cloth. 

  Depending on the variants, there is a battery 

installed in the device. This must not be 
opened with force, come into contact with 
water, short-circuited or exposed to 
temperatures above 80 °C. 

  Discharged batteries, electronic devices or 

components that are no longer required must 
be disposed of as hazardous waste at 
suitable collection points. 

  If multiple meters are used in a billing unit, 

similar types of device shall be used in order 
to obtain an accurate calculation of the 
consumption. 

 

For devices with main power supply: 

 
The main power supplies (230 V AC or 24 V AC) 
must have a 6 A-fuse on the installation side for 
safety. 

The connection must only be carried 

out by an authorized person trained for this.

 

Furthermore, observe the recognized rules for the 
technology and in particular, VDE 0100. 
 
Voltage: 

220 ... 240 V AC 
or 24 V AC 

Frequency:  

 

50/60 

Hz 

Max. power consumption: 

0.5 VA 

Cable length:   

 

approx. 1.1 m 

 
 

3. Tools Required 

  Suitable open-end spanner or adjustable 

spanner for the connecting bolts or flanged 
bolts. 

  Philips screwdriver 0.5 

3 for terminal 

connection block 

  Allen key, size 3 for wall adapter 

  Side cutters for lockwire 

  Open-end spanner AF 24 (sleeves) 

 

4. Combination of the Sub-assemblies 

 
A complete measurement unit comprises of three 
sub-assemblies: 
These are available as a standard set which 
includes: 

 Flow 

sensor 

  Calculator unit PolluTherm 

  A pair of temperature sensors 

 
Flow sensor: 

Size  

Output 

pulse 

qp 0.6 to 6 

1 litre/pulse 

qp 10 to 60 

10 litres/pulse 

 
Calculator: 

Input pulses

 1 

litre/pulse 

  10 

litres/pulse 

 
Temperature sensors: 

Length 

 45 

mm 

  100 

mm 

  150 

mm 

 
During the installation it must be ensured that the 
flow sensor and the calculator have the same 
pulse value! 
 
 
 
 
 

Summary of Contents for SENSUS PolluTherm





















Reviews: