Operation Manual
38
Operator Cab
Q. DEF GAUGE / LOW DEF LEVEL INDICATOR
The DEF Gauge indicates the quantity of fluid in the Diesel Ex-
haust Fluid (DEF) tank. The total capacity of the DEF tank is 5
gallons.
The DEF tank should be filled after every fuel refill.
DEF should be added when the Low DEF (Diesel Exhaust Fluid)
Level indicator is displayed.
R. FUEL GAUGE AND LOW FUEL INDICATOR
The fuel gauge indicates the approximate quantity of fuel
in the tank. The total capacity of the fuel tank is 50 gallons.
When the fuel level is below 10%, the low fuel level indicator
turns red.
S. ENGINE TEMP GAUGE AND HIGH TEMP INDICATOR
The Engine Temp Gauge indicates the temperature of the
coolant in the engine cooling system. After starting the Tele-
handler, allow time for the Engine Temp Gauge to begin mov-
ing before operating the Telehandler. After the engine has
sufficiently been warmed up, normal engine coolant tempera-
ture should read between 1800 to 2000 F.
T. OIL PRESSURE INDICATOR
The Oil Pressure Indicator monitors the engine oil pressure. At
normal operating pressure it stays green (above 20 psi). Be-
tween 12-20 psi it turns yellow and below 10 psi it becomes
red. If the indicator turns red (shows oil pressure below 10 psi)
and the Oil Pressure Warning (red) is displayed, stop the Tele-
handler, follow proper shut down procedures, tag Telehandler
with “Do Not Operate” tags, and have a qualified mechanic
service or repair the Telehandler BEFORE placing it into ser-
vice again.
U. VOLTAGE GAUGE
The Voltage Gauge indicates the amount of charge (in Volts).
Normal system voltage is between 12.5 and 14 Volts. If the
voltage gauge shows abnormal readings, stop the Telehandler,
follow proper shut down procedures, tag Telehandler with “Do
Not Operate” tags, and have a qualified mechanic service or
repair the Telehandler BEFORE placing it into service again.
V. MESSAGE / STATUS DISPLAY
Displays engine status messages or additional warnings.
W. STOP INDICATOR
The Engine Stop Indicator is displayed when the engine is shut
down. It is displayed with a flashing Check Engine Indicator
when an engine shutdown is imminent.
X. CHECK ENGINE/GENERAL WARNING INDICATOR
In case of any engine errors, the general error lamp of the
engine will be activated. Whenever the error lamp is active, a
fault code is stored in the error memory.
F. WAIT TO START
The Wait to Start Indicator is displayed when the key switch is
moved to the RUN position. Wait until the indicator goes out
before starting the engine.
G. ENGINE SERVICE REQUIRED
The Engine Service Required Indicator will be displayed when
a maintenance interval has been exceeded.
H. REGENERATION MENU
Pushing the soft button adjacent to the Regen Menu indica-
tor displays the exhaust system regeneration mode with the
available options.
I. REAR AXLE LOCKED
The Rear Axle Locked Indicator illuminates when the
Telehandler is in the axle lock mode. The rear axle locks when
the parking brake is set to ON (engaged), or the transmission
is in NEUTRAL or the service brake is applied, and when the
boom is above 100. If the Rear Axle Locked Indicator does not
illuminate when the Telehandler is in the axle lock mode, stop
the Telehandler, follow proper shut down procedures, tag
Telehandler with “Do Not Operate” tags, and have a qualified
mechanic service or repair the Telehandler BEFORE placing it
into service again.
J. REAR AXLE CENTERED
Rear Axle Centered Indicator will be displayed when the rear
wheels are aligned perpendicular to the rear axle. The rear
wheels should be centered before changing steering modes.
K. REAR-VIEW CAMERA
The rear-view camera operates automatically when the Tele-
handler is in reverse or by pressing the soft button CAM.
L. TACHOMETER
The Tachometer indicates engine RPM using a 0-2500 RPM an-
alog dial and also using digital RPM readout at the bottom of
the tachometer display
M. HOURMETER
The Hourmeter indicates and records engine operating hours.
Use the Hourmeter to establish a Telehandler maintenance
schedule.
N. DIGITAL CLOCK
O. DIRECTION OF TRAVEL INDICATOR
Displays the direction of travel selected: Forward or Reverse.
P. TRANSMISSION GEAR INDICATOR
Displays the transmission gear selected. The available
positions are: 1, 2, 3, and Automatic. Automatic is displayed as
A1, A2, or A3, with the numbers representing the current gear
the transmission is in.
