Xray NT1 2023 Instruction Manual Download Page 10

Page: 10 / 52

1. REAR GEAR DIFFERENTIAL

14.70g

16.70g

TO ENSURE YOU HAVE THE SAME AMOUNT OF OIL FROM REBUILD TO REBUILD, DO THE FOLLOWING:

➋

Slowly pour oil into the diff and watch the weight.

Add 2.0g of oil into the diff. The approximate weight

of the diff including oil is 16.70g.

#107865 HUDY Ultimate Digital Pocket Scale 300g±0.01g

➊

Put the diff (without oil) on the scale and check the weight

(approximately 14.70g).

14 70

16 70

980210

P 2x10

972050

O 5x2

964050

S 5x15x0.3

962051

S 5x10x0.2

➊

➋

➌

➍

➎

➏

Fill differential up to the top of

the diff pins. DO NOT fill the diff

to the top of the housing.

Remove the nozzle of the bottle

to allow easy filling of the diff.

Silicone oil

60.000cSt

Silicone oil

60.000cSt

DETAIL

Use tweezers to insert pin.

STEP

➎

DETAIL

DETAIL

14.70g + 2.0g = 16.70g

OIL

Summary of Contents for NT1 2023





















































Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands

Xray NT1 2023, Instruction Manual

Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands