Xray NT1 2023 Instruction Manual Download Page 34

Page: 34 / 52

7. FUEL TANK & ELECTRONICS

301324 FRONT BODY MOUNT SET +2MM HEIGHT

303241 BALL UNIVERSAL 5.8 MM HEX (4)

332630 ADJ. TURNBUCKLE L/R 22 MM - HUDY SPRING STEEL™ (2)

332660 COMPOSITE STEERING & SERVO BALL JOINT 5.8 MM (4+2)

336001 COMPOSITE RECEIVER CASE - COMPACT SIZE

336115 GRAPHITE RADIO PLATE - MULTI-FLEX™

336116 GRAPHITE FRONT UPPER BRACE

336117 GRAPHITE FRONT UPPER BRACE - TRIANGLE

336120 COMPOSITE STEERING SERVO HOLDER - SET

336131 ALU STEERING SERVO MOUNT - BLACK (2)

336151 COMPOSITE BATTERY PLATE

336191 COMPOSITE ROLL-OVER BAR WITH EYELET

336200 STEERING SERVO ARMS - SET

338602 FUEL TANK 75CC - SET - V3

338685 FUEL TANK MOUNTING GROMMET (3)

358941 COMPOSITE TUBING HOLDER FOR FUEL TANK (2)

371345 COMPOSITE SHIM FOR BODY POST (2)

902258 HEX SCREW SH M2.5x8 (10)

902306 HEX SCREW SH M3x6 (10)

902308 HEX SCREW SH M3x8 (10)

902310 HEX SCREW SH M3x10 (10)

902312 HEX SCREW SH M3x12 (10)

903255 HEX SCREW SFH M2.5x5 (10)

903306 HEX SCREW SFH M3x6 (10)

903308 HEX SCREW SFH M3x8 (10)

905258 SCREW PHILLIPS 2.5x8 (10)

911312 HEX SCREW FL. SH M3x12 (10)

971035 SILICONE O-RING 3.5x2 (10)

981212 PIN 2x12 (10)

911312

SHF M3x12

903308

SFH M3x8

BAG

Ensure that bar is square

with radio plate.

Use 3mm lowering

shims ONLY when using

optional micro-size

receiver battery pack.

IMPORTANT!
Do not tight fully, is important that the

bar has some play. If the bar is tightened

too much, it can tweak the radio plate.

Install insert ONLY if fuel

capacity is over the limit.

905258

2.5x8

OPTION ONLY

CUTAWAY VIEW

IMPORTANT!
Tighten the screws gently to make

sure that the O-ring does not bind.

The purpose of the O-rings is to

allow movement of the fuel tank

in all directions.

971035

O 3.5x2

Radio plate

CUTAWAY VIEW

3x8mm

3x12mm

2.5x8mm

371345

981212

902306

(NOT INCLUDED)

336191

903308

911312

902312

Throttle Servo

(NOT INCLUDED)

Servo Screw

(NOT INCLUDED)

336120

971035

338685

338602

902308

902310

303241

902308

336151

Receiver Battery

(NOT INCLUDED)

903308

Personal Transponder

(NOT INCLUDED)

902308

902306

301324

Steering Servo

(NOT INCLUDED)

336131

303241

336200

905258

338602

332660

332630

336115

336001

902258

902306

903255

358941

336117

336116

Summary of Contents for NT1 2023





















































Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands

Xray NT1 2023, Instruction Manual

Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands