Xray NT1 2023 Instruction Manual Download Page 26

Page: 26 / 52

4. FRONT SUSPENSION

FRONT ROLL CENTER

ADJUSTMENT

NOTE ORIENTATION

SHORT

LONG

Tighten composite hex nuts

using HUDY tool #107581.

#337252 Alu nut

#337254 Composite cup

902306

SH M3x6

➊

➋

➌

➍

➎

1mm

2mm

3mm

901306

SB M3x6

NOTE ORIENTATION

STEP DETAIL

➎

DETAIL

FRONT UPPER ARMS

#332135 GRAPHITE OPTION
#332134 SOFT

OPTION

#332133 HARD

INCLUDED

#332132 MEDIUM

OPTION

STEERING BLOCK

#332212

1° RIGHT M OPTION

#332212-H 1° RIGHT H INCLUDED
#332213

0° RIGHT - OPTION

#332222

1° LEFT M OPTION

#332222-H 1° LEFT H INCLUDED
#332223

0° LEFT

- OPTION

INITIAL SETTING

Composite eccentric

bushings

INITIAL SETTING

Composite eccentric

bushings

Pivot balls must move freely.

During initial assembly, tighten

each composite hex nut until the

pivot ball starts to bind, then

loosen slightly. Verify that the

pivot balls move freely.

LONG

SHORT

Summary of Contents for NT1 2023





















































Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands

Xray NT1 2023, Instruction Manual

Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands