Xray NT1 2023 Instruction Manual Download Page 7

Page: 7 / 52

GEAR DIFF ADJUSTMENT

1. FRONT GEAR DIFFERENTIAL & SOLID AXLE

14.70g

TO ENSURE YOU HAVE THE SAME AMOUNT OF OIL FROM REBUILD TO REBUILD, DO THE FOLLOWING:

➋

Slowly pour oil into the diff and watch the weight. Add 2.0g of oil

into the diff. The approximate weight of the diff including oil is 14.70g.

Push down

Wait approx. 5min

Rotate

#107865 HUDY Ultimate Digital Pocket Scale 300g±0.01g

12.70g + 2.0g = 14.70g

12.70g

➊

Put the diff (without oil) on the scale and

check the weight (approximately 12.70g).

14 70

12 70

964031

S 3.5x10x0.2

Silicone oil

300.000cSt

Silicone oil

300.000cSt

980210

P 2x10

972050

O 5x2

964050

S 5x15x0.3

962051

S 5x10x0.2

CUTAWAY VIEW

STEP

Use tweezers to insert pin.

➊

➋

➌

➍

➎

➏

➎

DETAIL

DETAIL

Fill differential up to the top of

the diff pins. DO NOT fill the diff

to the top of the housing.

Remove the nozzle of the bottle

to allow easy filling of the diff.

OIL

#335081

ALU DIFFERENTIAL PIN - HARDCOATED (2)

#104002

HUDY AIR VAC – VACUUM PUMP

Summary of Contents for NT1 2023





















































Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands

Xray NT1 2023, Instruction Manual

Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands