Xray NT1 2023 Instruction Manual Download Page 23

Page: 23 / 52

4. FRONT SUSPENSION

302080 CASTER CLIPS SET 4+3+2+1 MM (2)

302663 COMPOSITE BALL JOINT 4.9MM - OPEN - V2 (8)

303123-K ALU SHIM 3x6x2.0MM - BLACK (10)

303454 BALL JOINT 4.9MM - OPEN (4)

305231 DRIVE SHAFT COUPLING - HUDY SPRING STEEL™

332018 ALU LOWER BULKHEAD FRONT RIGHT - BLACK - SWISS 7075 T6

332028 ALU LOWER BULKHEAD FRONT LEFT - BLACK - SWISS 7075 T6

332039 ALU UPPER CLAMP FRONT (L+R) - BLACK - SWISS 7075 T6

332070 COMPOSITE ADJUST. BALL-BEARING HUB (4)

332071 COMPOSITE BALL-BEARING HUB (4)

332083 GRAPHITE SHOCK TOWER FRONT 2.5MM

332113 COMPOSITE SUSP. ARM FRONT LOWER FOR WIRE ANTI-ROLL BAR - HARD

332133 COMPOSITE SUSP. ARM FRONT UPPER WITH HOLE - HARD

332170 COMPOSITE SUSP. ARM BACKSTOP (2)

332212-H COMPOSITE STEERING BLOCK RIGHT FOR AERO DISC - HARD

332222-H COMPOSITE STEERING BLOCK LEFT FOR AERO DISC - HARD

332291 ALU EXTENSION FOR STEERING BLOCK - SWISS 7075 T6 (2)

332411 COMPOSITE FRONT ANTI-ROLL BAR HOLDER & ECCENTRIC W/O UPSTOP (2+2)

332432 ALU FRONT ANTI-ROLL BAR HUB (2)

332482 ANTI-ROLL BAR FRONT 2.2 MM

332711 ALU LOWER 2-PIECE FRONT SUSPENSION HOLDER - BLACK (1)

332733 ALU UPPER ARM HOLDER RIGHT - BLACK - SWISS 7075 T6 - SET

332743 ALU UPPER ARM HOLDER LEFT - BLACK - SWISS 7075 T6 - SET

333443-L ALU ANTI-ROLL BAR COLLAR o2.2 - LIGHTWEIGHT (2)

335215 CVD AXLE - SUPER LIGHT - HUDY SPRING STEEL™

335225 CVD DRIVE SHAFT - FRONT - HUDY SPRING STEEL™

335250 ALU WHEEL HUB 12MM - BLACK (2)

BAG

335430 PUR®-REINFORCED DRIVE BELT FRONT 5 x 186 MM

337211 FRONT LOWER INNER PIVOT PIN (2)

337222 FRONT UPPER PIVOT PIN WITH FLAT SPOT (2)

337253 COMPOSITE ADJUSTING NUT M10x1 WITH BALL CUP (4)

337256 STEEL PIVOT BALL 8.4 MM (2)

337259 STEEL PIVOT BALL 8.4 MM o2.6 L=25MM (2)

343483-K ALU CUTTED ANTI-ROLL BAR COLLAR o2.3 - BLACK (2)

362316 OPEN ECCENTRIC BUSHING SET (2)

362650 BALL END 4.9MM WITH THREAD 6MM (2)

901302 HEX SCREW SB M3x2.5 (10)

901303 HEX SCREW SB M3x3 (10)

901306 HEX SCREW SB M3x6 (10)

901312 HEX SCREW SB M3x12 (10)

901410 HEX SCREW SB M4x10 (10)

902306 HEX SCREW SH M3x6 (10)

902308 HEX SCREW SH M3x8 (10)

902312 HEX SCREW SH M3x12 (10)

902314 HEX SCREW SH M3x14 (10)

903305 HEX SCREW SFH M3x5 (10)

903308 HEX SCREW SFH M3x8 (10)

930508 BALL-BEARING 5x8x2.5 STEEL SEALED - OIL (2)

941016 BALL-BEARING 10x16x4 RUBBER SEALED - OIL (2)

980210 PIN 2x10 (10)

335000 FRONT GEAR DIFFERENTIAL - SET

#335432

LOW FRICTION DRIVE BELT FRONT

5.0 x 186 MM

903305

FRONT SUSPENSION ARMS

#332112 MEDIUM OPTION
#332113 HARD

INCLUDED

#332113-G GRAPHITE OPTION

FRONT UPPER ARMS

#332135 GRAPHITE OPTION
#332134 SOFT

OPTION

#332133 HARD

INCLUDED

#332132 MEDIUM

OPTION

332028

337222

302080

332743

902308

333443-L

337211

332711

332133

332113

332170

303123-K

903308

930508

332071

332482

343483-K

980210

335225

941016

332222-H

902308

332291

335250

335000

941016

901303

305231

335215

337256

941016

337253

901303

335430

332070

332733

332039

332018

903308

332212-H

903305

903308

902312

302663

362650

901302

332039

902306

901306

902308

302080

362316

901312

332083

901410

332411

332432

902314

332711

903305

303454

902306

337259

362316

Summary of Contents for NT1 2023





















































Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands

Xray NT1 2023, Instruction Manual

Search results

Summary of Contents for NT1 2023

Reviews:

Related manuals for NT1 2023

Brands by name

Popular brands