XMODUS AL5068S At Commands Reference Manual Download Page 46

Page: 46 / 46

XM1240S AT Commands Reference Manual

No. AL5068S-A00-106

xmodus swiss GmbH

46 / 46

A. APPENDIX

A.1

TABLE OF ISDN CAUSES (ETSI CAUSE VALUES)

Dec/Hex

Cause name

1 / 0x81

Unallocated (unassigned) number

2 / 0x82

No route to transit network

3 / 0x83

No route to destination

6 / 0x86

Channel unacceptable

7 / 0x87

Call awarded and being delivered in an established channel

16 / 0x90

Normal clearing

17 / 0x91

User busy

18 / 0x92

No user responding

19 / 0x93

No answer from user (user alerted)

20 / 0x94

No answer from user (device off)

21 / 0x95

Call rejected

22 / 0x96

Number changed

26 / 0x9A

Non selected user clearing

27 / 0x9B

Destination out of order

28 / 0x9C

invalid number format

29 / 0x9D

Facility rejected

30 / 0x9E

Response to STATUS ENQUIRY

31 / 0x9F

Normal disconnect, unspecified

34 / 0xA2

No circuit/channel available

38 / 0xA6

ISDN network out of order

41 / 0xA9

Temporarily failure

43 / 0xAB

Access information discarded

44 / 0xAC

Requested circuit/channel not available

46 / 0xAE

Precedence call blocked

47 / 0xAF

Resource unavailable, unspecified

49 / 0xB1

Quality of service unavailable

50 / 0xB2

Requested facility not subscribed

53 / 0xB5

Outgoing calls barred within CUG

55 / 0xB7

Incoming calls barred within CUG

57 / 0xB9

Bearer capability not authorized

58 / 0xBA

Bearer capability not presently available

63 / 0xBF

Service or option not available, unspecified

65 / 0xC1

Bearer capability not implemented

66 / 0xC2

Channel type not implemented

69 / 0xC5

Requested facility not implemented

70 / 0xC6

Only restricted digital information bearer capability is available

79 / 0xCF

Service or option not implemented, unspecified

81 / 0xD1

Invalid call reference value

82 / 0xD2

Identified channel does not exist

83 / 0xD3

A suspended call exists, but this call identity does not

84 / 0xD4

Call identity in use

85 / 0xD5

No call suspended

86 / 0xD6

Call having the requested call identity has been cleared

87 / 0xD7

User not member of CUG

88 / 0xD8

Incompatible destination

90 / 0xDA

Non-existent CUG

91 / 0xDB

Invalid transit network selection

95 / 0xDF

Invalid message, unspecified

96 / 0xE0

Mandatory information element missing

97 / 0xE1

Message type non-existent or not implemented

98 / 0xE2

Message not compatible with call state or message type non-
existent or not implemented

99 / 0xE3

Information element /parameter non-existent or not implemented

100 / 0xE4

Invalid information element contents

101 / 0xE5

Message not compatible with call state

102 / 0xE6

Recovery on timer expiry

103 / 0xE7

Parameter non-existent or not implemented, passed on

111 / 0xEF

Protocol error, unspecified

127 / 0xFF

Network interworking error, unspecified

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for AL5068S















































Search results

Summary of Contents for AL5068S

Reviews:

Related manuals for AL5068S

Brands by name

Popular brands

XMODUS AL5068S, At Commands Reference Manual

Search results

Summary of Contents for AL5068S

Reviews:

Related manuals for AL5068S

Brands by name

Popular brands