XMODUS AL5068S At Commands Reference Manual Download Page 31

Page: 31 / 46

XM1240S AT Command Reference Manual

No. XM1240S-A00-106

xmodus swiss GmbH

31 / 46

5. MESSAGES

5.1 AT Commands relating to message formats.

5.1.1 ATVn

Result Format.

ATV0

Result is presented as numbers (followed by <cr>)

ATV1

Result is presented as text

(default)

5.1.2 ATWn

ISDN Extended Result Codes

ATW0

Result is presented without <xx> and <nr>

(default)

<xx> = ISDN error cause (see also section 5.2)

<nr> = calling party number (see also section 5.2)

ATW1

Result is presented with <xx> and <nr>

<xx> = ISDN error cause [decimal] (see also section 5.2)

<nr> = calling party number (see also section 5.2)

ATW2

Result is presented with <xx> and <nr>

<xx> = ISDN error cause [text format] (see also section 5.2)

<nr> = calling party number (see also section 5.2)

ATW3

same as ATW2 but <nr> at CONNECT message is

replaced with <datetime> element of L3 frame.

5.1.3 ATXn

Extented Result Codes

Sets the types of result messages (see section 5.2)

ATX0

"CONNECT" only (without line speed)

ATX1

"CONNECT" with line speed, "BUSY", "NO DIALTONE" not used

ATX2

"CONNECT" with line speed, "BUSY" not used

ATX3

"CONNECT" with line speed, "NO DIALTONE" not used

ATX4

"CONNECT" with line speed, all messages used

(default).

5.1.4 AT%Wn

Message compatibility modes

Sets the compatibility of result messages (see section 5.2)

AT%W0

AL5500S Mode.

S40 = 0

AT%W1

AL5064S Mode.

S40 = 1

(default)

AT%W2

Modem Mode.

S40 = 2

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for AL5068S















































Search results

Summary of Contents for AL5068S

Reviews:

Related manuals for AL5068S

Brands by name

Popular brands

XMODUS AL5068S, At Commands Reference Manual

Search results

Summary of Contents for AL5068S

Reviews:

Related manuals for AL5068S

Brands by name

Popular brands