XMODUS AL5068S At Commands Reference Manual Download Page 15 | Manualshive

Page: 15 / 46

background image

XM1240S AT Command Reference Manual

No. XM1240S-A00-106

xmodus swiss GmbH

15 / 46

3.3.15 ATXn

Extented Result Codes

This command selects the subset of the result code messages used by the modem to
inform the DTE of the results of commands. The information below is based upon the
default implementation of the X results table. Table 5-2 indicates the messages which
are enabled for each X value. If the modem is in modem mode, the only message
sent to indicate a connection is “CONNECT” without a speed indication. Please see
also Chapter 5.

ATX0

CONNECT only (no line speed), send only OK, CONNECT, RING,

NO CARRIER and ERROR result codes.

ATX1

CONNECT XXXX, send only OK, CONNECT, RING, NO CARRIER,
and ERROR, . If busy tone detection is enforced and busy tone is
detected, NO CARRIER will be reported instead of BUSY.

ATX2

CONNECT XXXX, send only OK, CONNECT, RING, NO

CARRIER, NO DIALTONE and ERROR. If busy tone detection is

enforced and busy tone is detected, NO CARRIER will be reported

instead

of

BUSY

ATX3

CONNECT XXXX, Enables reporting of busy tones; send only OK,
CONNECT, RING, NO CARRIER, ERROR, BUSY and NO DIALTONE.

ATX4

CONNECT XXXX, Enables reporting of busy tones; send all
messages.

3.3.16 ATZ

Load stored settings

The isdn-modem performs a soft reset and restores (recalls) the configuration profile.
Must be the last command in an AT command line.

Result codes:

OK

All manuals and user guides at all-guides.com

«
...
13
14
15
16
17
...
»

Summary of Contents for AL5068S















































Reviews:

No comments

Related manuals for AL5068S

Brand: Elpro Technologies Pages: 62

Brand: Virgin Pages: 44

Brand: Vaisala Pages: 20

Brand: ABB Pages: 6

Photo Backup STICK

Brand: Paraben Pages: 39

TouchNet 89-9150

Brand: Toro Pages: 2

Netgear Nighthawk D7800

Brand: TPG Pages: 2

D-Link COVR-1102

Brand: TPG Pages: 2

TP-Link VX420-G2v

Brand: TPG Pages: 4

Brand: NETGEAR Pages: 28

MultiConnect microCell MTCM2-L4G1

Brand: Multi-Tech Pages: 27

Brand: Broadxent Pages: 60

Brand: C-motech Pages: 15

Brand: ERE Pages: 17

Brand: RSI Pages: 9

Brand: Flightcell Pages: 12

Brand: TC Communications Pages: 20

Brand: Omni Instruments Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands