XMODUS AL5068S At Commands Reference Manual Download Page 36 | Manualshive

Page: 36 / 46

background image

XM1240S AT Commands Reference Manual

No. XM1240S-A00-106

xmodus swiss GmbH

36 / 46

5.5 CALLING NUMBER REPORT (CLIP)

The CLIP (calling party number) can be reported together with the “CONNECTED” or
the “RING” messages. To enable this, ATW1 or ATW2 must be selected (see
description at 3.3.14). The CLIP can be reported also by issuing the command
AT$O. This way, only the CLIP number is reported. If the ISDN Modem is used at the
public network, then the full call number of the remote site (including area code) is
reported.

Example:

ATW1



send to modem

OK



received from modem

RING

0448903322



received from modem

ATA



send to modem

CONNECTED (V.120) 0448903322



received from modem

5.6 ISDN ERROR CAUSE REPORT

The ISDN error causes can be reported together with the “RELEASED” or “NO
CARRIER” message. If ATW1 is selected, the error causes are reported in decimal
form. If ATW2 is selected, the error causes are reported in text format. The coding
scheme is as per ETSI definition.

Example 1:

ATW1



send to modem

OK



received from modem

ATD0449121234



send to modem

RELEASED 17



received from modem

Example 2:

ATW2



send to modem

OK



received from modem

ATD0449121234



send to modem

RELEASED USER BUSY



received from modem

All manuals and user guides at all-guides.com

all-guides.com

«
...
34
35
36
37
38
...
»

Summary of Contents for AL5068S















































Reviews:

No comments

Related manuals for AL5068S

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 21

Brand: ICP DAS USA Pages: 6

Brand: T-Mobile Pages: 10

Brand: FALCOM Pages: 31

Brand: Atel Pages: 9

Brand: Nokia Pages: 62

Brand: Motorola Pages: 29

Brand: Zte Pages: 30

Brand: PPL Pages: 2

Brand: Enfora Pages: 41

Brand: Hughes Pages: 61

Brand: SMC Networks Pages: 2

Brand: Electronics Is Fun Pages: 35

SURFboard SBG6950AC2

Brand: CommScope Pages: 64

Hylas 2 - freedomsat

Brand: Hughes Pages: 12

Speed USB STICK U01

Brand: KDDI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands