Xerox WIDE FORMAT 721P Operator'S Manual Download Page 63 | Manualshive

Page: 63 / 72

background image

USER MODES

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

55

User Mode 4 (High Power Saver Mode) “U4”

When the High Power Saver Mode is enabled, the printer switches
off power to the Printer Fuser Assembly after a predetermined time
of inactivity. If the printer does not receive a print job or a copy job
for the time selected in this mode, the printer will enter the High
Power Saver Mode to save power consumption.

The High Power Saver Mode saves more power than the Low
Power Saver Mode and the recovery time is longer.

If a print or copy job is detected by the printer, the printer will then
enter the Warm up Mode prior to the start of the job to heat the
Fuser Assembly to 178

°

C.

The green LED Light inside of the Menu Button flashes when the
printer is in a power saver mode.

1. To enter User Mode 4:

Press the [Menu] Key 4 times when the printer is in the Standby
(idle) Mode.

The [Menu] Key lights green and the Status Display indicates “U4.”
Flashing on the left side of the display. The time interval is shown
on the right side of the display.

NOTE

: Factory default is On and set to 90 minutes.

2. Press

[Enter]

The status (on or off) is displayed. If the status is off, High Power
Saver is disabled.

To change the status, press [Enter] and then the [ --> ] Key or the
[ <-- ] Key.

Press [Enter] again to gain access to the time interval.

To change the time, press [ --> ] Key to increase) and [ <-- ] Key to
decrease, then press [Enter] to save the data.

The display value is “minute”, and the selectable ranges are 10,
15, 20, 30, 40, 50, 60, 90, 120, 180 and 240.

Menu

Enter

Online

Press [Menu] 4 times

Menu

Enter

Online

Menu

Enter

Online

«
...
61
62
63
64
65
...
»

Summary of Contents for WIDE FORMAT 721P









































































Reviews:

No comments

Related manuals for WIDE FORMAT 721P

Brand: Canon Pages: 86

Brand: Canon Pages: 20

Brand: Samsung Pages: 9

Bixolon SRP-500

Brand: Samsung Pages: 27

550N - CLP Color Laser Printer

Brand: Samsung Pages: 288

2 COLOR THERMAL PRINTER SRP-275

Brand: Samsung Pages: 8

Brand: Samsung Pages: 6

Brand: Samsung Pages: 91

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: Canon Pages: 2

Aficio SP C420DN

Brand: Ricoh Pages: 4

Brand: SEWOO Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands